The Americana Trailer Wheel Center Cap - Chrome - 3.19" Pilot - 14" Wheels # AM90098 will fit the 13 inch American wheel just like the Replacement Center Cap for 13" and 14" Aluminum Hi-Spec Series 06 Wheels - Black # AM54FR. They are the same with the exception of the finish.
view full answer...
I reached out to my contact at Phoenix USA and the Phoenix USA Front Hub Cover w/ Pop Out - 8 on 275mm - 33mm Lug Nuts - ABS Plastic # PXQ822F you were looking at will work with your 2014 Thor Challenger with 8 lug 22.5" wheels as long as your factory lug nuts are 33mm. For the matching rear covers you would want the # PXQ822R.
If your factory lug nuts are 30mm you will need the Front # PXQ820F and Rear # PXQ820R instead.
For either of these options you will need at least 1/4" of... view full answer...
I have a possible solution for you, but the Replacement Phoenix USA Rear Wheel Center Cap # PXPH1764 is actually designed to be used on 10 lug applications, not 8 lug.
It sounds like Replacement Phoenix USA Rear Wheel Center Cap - 6-1/2" or 8-1/4" Hub Diameter - Stainless # PXPH1843 may work for you. This is a fit for wheels that are 8 on 275mm and it fit hubs with a diameter of 6-1/2" or 8-1/4", so if your RV matches these specs then you are good to go. This is just the cover, but... view full answer...
Sorry to hear that the Americana Baby Moon Trailer Wheel Center Cap # AM90086 are too small for your 1959 Canned Ham Trailer.
In order to get your the right center cap this time, you'll want to verify what your pilot hole diameter is. The Americana Trailer Wheel Center Cap # AM90091 will work great if your pilot hole diameter is 3.19".
To find and verify your pilot hole diameter, you'll need to measure the center hole on your wheel.
For instance, the Dextstar Dual Wheel With Offset... view full answer...
The depth of the Americana Baby Moon Trailer Wheel Center Cap part # AM90086 is 2-3/4". The Americana Pointed Top Baby Moon Trailer Wheel Center Cap part # AM981306 has slightly more depth at 3" so they should both clear most grease caps just fine. view full answer...
Since your bracket and center bolt piece is damaged, I recommend to use the Phoenix USA Wheel Center Cap - 6-1/2" Axle Diameter part # PXQ2010L which comes with the replacement left hand threaded center bolt and bracket. The OEM replacement part is part # PXPH1764 but that requires you to re-use your existing bolt and bracket which you don't have.
The Phoenix USA Wheel Center Cap part # PXQ2010L is what you need as long as your axle is 6-1/2" which is common for the Freightliner. view full answer...
The part numbers you provided match up with the Replacement Phoenix USA Rear Wheel Center Cap part # PXPH1764 and Replacement Center Attachment Bolt part # PHX84FR. I don't have any way to verify these to the chassis but so long as the pictures match and the dimensions are close they should fit. view full answer...
There are a few trailer wheel center caps that fit pilot hole diameters of about 5 inches, but not precisely 5 inches, which are the following:
- 4.90" Pilot Diameter: Americana Trailer Wheel Center Cap - Stainless Steel # AM90156C
- 4.90" Pilot Diameter: Trailer Wheel Center Cap, Stainless Steel # 490EZ-SS
- 5.12" Pilot Diameter: Americana Trailer Wheel Center Cap - 5.12" - Chrome # AM90083
- 5.15" Pilot Diameter: Americana Trailer Wheel Center Cap - 5.15" Pilot - Stainless... view full answer...
The Wheel Masters Wheel Covers - 16", 8-Lug Wheels - 8 HH - Front/Rear # WM3160B0 are stainless steel. The Namsco Wheel Covers - 16", 8-Lug Wheels - 8 HH - Front/Rear # NA7160B0 are also are also corrosion resistant but made of plastic with a metal looking mirror finish. They both come with a 1 year limited warranty but the Namsco option does not come with the valve extensions.
We do not break up sets so if you need additional covers the best option is the Namsco which will allow... view full answer...
When considering center caps for your wheels on your 2006 Triton boat trailer, you need to know the wheel diameter, lug pattern, and center hole diameter. For example, the Taskmaster Trailer Wheel Center Cap w/ Snap-In Plug # TA54FR fits 15-16 inch wheels with a 6-lug pattern that has a 4-1/2 inch center diameter.
Unfortunately, I do not have the wheel specs for your specific trailer. However, if you respond to this answer with those measurements, I would be happy to assist you in finding... view full answer...
I have a cap solution for you. Unfortunately, the Americana Trailer Wheel Center Cap w/ Plug - Chrome Plated # AM90195 will not fit the Loadstar ST205/75D14 Bias Trailer Tire with 14" Aluminum Wheel # AM3S434 because the Americana cap is designed to fit a 3.33" pilot diameter. The wheel has a 3.13" pilot diameter.
With that being said, a great alternative for a 5-bolt 3.13" pilot diameter wheel is the Lionshead Trailer Wheel Center Cap - 3.19" Pilot # LHCS102 along with the Snap-In... view full answer...
Yes, the Phoenix USA Front Hub Cover w/ Pop Out - 8 on 275mm - 33mm Lug Nuts - ABS Plastic, part # PXQ822F, should fit with no problem. I have included a product description and a video review link below. view full answer...
Manufacturers do not list the parts they use on their RV's so you'll need to measure the bolt pattern and hub size of your current setup to determine the compatibility of the Phoenix USA Rear Wheel Center Cap # PXQ2020XL.
The # PXQ2020XL fits a bolt pattern of 10 on 285mm and hub diameter of 8-1/4". view full answer...
In order to confirm whether the Phoenix USA Front Hub Cover # PXQ820F fits your 8-lug pattern with 30mm nuts, you need to first make sure that you have a bolt pattern of 8 on 275mm. This is the bolt pattern that the # PXQ820F is designed to fit. The 275mm is the number that defines the diameter of the circle the bolts form.
In order to determine if you indeed have a 8 on 275mm, I went ahead and attached a help article that walks you through the measurement process. Feel free to respond... view full answer...
We have the Replacement Wheel Master Lug Nut Cover for Wheel Liner part # WMRMT9061 available. These are designed to go over the keeper nuts to give you a nice clean look.
We also offer a 33mm part # WM9005-6, 7/8" Covers part # WM8019, 1" Covers part # WM8010 or the 1-1/16" Covers part # WM8011. view full answer...
Based on the wheel information you've provided, you have something like the Dexstar Steel Mini Mod Trailer Wheel # AM20363, in which the Lionshead Trailer Wheel Center Cap w/ Snap-In Plug # LHCS102-SI60C you reference, will work great as a replacement for what you currently have. view full answer...
Manufacturers do not list the wheel sizes they use on their trailers so the only way to know for certain is to measure the bolt pattern and pilot hole. Below I've attached our printable bolt pattern template as well as our help article on measuring the bolt pattern incase you don't have access to a printer.
If you did have a 15" x 5 on 4-1/2 wheel with a 3.19" pilot hole you would be able to use the Westlake ST205/75R15 Radial Trailer Tire w/ 15" Silver Mod Wheel - 5 on 4-1/2 - Load... view full answer...
We do have center caps for 3.19 inch pilot hole diameters, and 3.19 inches is 3-3/16 inches if you were to use a tape measure. So you can use either of the following:
- Lionshead Trailer Wheel Center Cap # LHCS102-SI60C
- Americana Trailer Wheel Center Cap # AM90175
Both have removable plugs in the center so you can easily access your E-Z Lube spindle's grease zerk. view full answer...
It sounds like the 3-1/8" depth of Americana Trailer Wheel Center Cap w/ Plug - Chrome Plated - 3.33" Pilot # AM90195 is not enough to clear your bearing buddy that you have installed. We do not have any deeper center caps that match the specs of this center cap.
It is not recommended to install a wheel center cap over the bearing buddy. This would sort of defeat the purpose of the bearing buddy since it is conveniently made to be greased without removing the wheel, but you would actually... view full answer...
Even though most threads on bolts use right-handed bolts/nuts, some special scenarios warrant a left-handed thread. When wheel accessories like the Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Left Thread # PXQ1020L use a left-handed thread, it is to avoid the added torque from bumps and rough terrain on your wheels. With these forces, right-handed bolts/nuts tend to come loose from those particular movements. For a hub cap, it is recommended to use a left-handed... view full answer...
I looked up the wheel bolt pattern of your 2004 Ford F-550 and it has a 10 on 225 mm bolt pattern. So for the rear you'd want the # PXQH2001R and then for the front you'd want the # PXQH2001F. view full answer...
Thanks for the picture and the dimensions. Based on what you have given me we have a couple of options for lug nut covers. The first is the Wheel Masters Lug Nut Covers - Stainless Steel - Ford - 1-1/16" - Qty 8
Item # WM8011 you referenced. This lug nut cover is 1 9/16" tall. This is for Ford wheels.
The second option is the Wheel Masters Lug Nut Covers - Stainless Steel - 1-1/2" - Qty 6 item # WM8012. I have attached a diagram with the dimensions of this lug nut cover. I recommend... view full answer...
The Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Right Thread # PXQ2020XL fits the rear motorhome wheels that has a hub diameter of 8-1/4 inches and a bolt pattern of 10 on 285 millimeters.
When it comes to the thread (either left or right), the names correspond to the direction that a screw’s thread wraps around its shaft. Most screws today use right-handed threads, and it’s rare to find a left-handed screw used in any application that doesn’t specifically... view full answer...
We do offer them in a set of four, Lug Nut Covers for Wheel Masters and Namsco Wheel Covers - Chromed ABS Plastic - Snap In - Qty 4, part # WM9003-4, to replace your them on your Replacement Namsco Wheel Cover - 19-1/2", 8-Lug Wheels - 10 HH - Front - Qty 1, part # NA719581. Unfortunately, we do not offer them individually.
I have included a product description link below. view full answer...
The Phoenix USA Rear Wheel Center Cap, part # PXQ1020L, fits 8-1/4" hubs and 8 on 275mm bolt patterns. If these match the specs on your rim, this will fit.
It looks like there are several bolt patterns available for the 22.5" Alcoa rims. If you let me know the bolt pattern, I can tell you definitely if this will work for you or recommend a different one if it doesn't. I've linked to an article we've written to help you measure your bolt pattern.
view full answer...
Yes, as long as your wheel features a 3.19" diameter pilot hole the Taskmaster Center Cap # CXF106B that you referenced will fit and work well. Its style compliments their Viking Series aluminum trailer wheels really well, which is why it's technically designed for those, but it uses a standard lip that will grab onto any brand wheel that's appropriately sized.
I have attached a short video review that you can check out as well. view full answer...
While we don't have the bath covering individually, we do sell the replacement center cap that comes with the covering that will fit your 2007 Triton bass boat trailer. That is the Americana Trailer Wheel Center Cap - Chrome - 3.19" Pilot - 14" Wheels # AM90098.
I went ahead and included a review of the cap as well as a picture of a customer review of a neighbor who used the cap on his 2007 Triton bass boat trailer. view full answer...
As long as your Keystone Montana is still equipped with 8 lug wheels, the Lionshead # LHCS109-SI60C should be the part you are looking for. I've attached a link to the page that lists all of our wheel caps and plugs just in case your wheels have changed from the OEM. view full answer...
You're looking for the Americana Trailer Wheel Center Cap - Black - 3.19" Pilot - 15" Wheels # AM90091B, which is the 15" version of the # AM54FR and have the black accents that you're looking for. view full answer...
To see if the Americana Trailer Wheel Center Cap # AM90113 you referenced would fit the wheel you have on your trailer you will need to measure the diameter of the hole in the center of your trailer wheel. If it is between 2.80 and 2.84 inches in diameter this cap would work well for you. view full answer...
In order to get the right size center cap you will have to measure the pilot diameter of the wheel. That is the center hole of your wheel. Once you get that measurement you will be able to find a center cap that fits your vehicle. You know the size of the wheel, 14". You know the bolt pattern, all you need is the pilot diameter measurement to find the correct size center cap. For example, the Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel - Qty 1, part # AM90086, works... view full answer...
As far as a left-threaded or right-threaded cap for your motorhome, right-handed threads run clockwise, and left-handed threads run counterclockwise. The reason for this difference is that some applications of screws can come loose with the motion of the vehicle. With that being said, left screws are the most beneficial for trailer caps, but it will not make a very significant difference.
If you need a recommendation for a wheel cap that will fit the diameter of your wheel, I would be... view full answer...
The Phoenix USA Wheel Center Cap part # PXPH1843 is a replacement for the Phoenix USA Wheel Center Cap part # PXQ1009 which is for a 6-1/2" diameter axle or the Phoenix USA Wheel Center Cap part # PXQ1020 which is for a 8-1/4" diameter axle. Therefore, if you have either of these kit then it will work for you but this would not be able to be installed on its own without the bracket and center bolt.
If you don't have the bracket and center bolt then you will need to install the kit and... view full answer...
We offer three LionsHead center caps. They are all stainless steel with a snap in plug. The three sizes are as follows:
3.19" Pilot Hole, Lionshead Trailer Wheel Center Cap w/ Snap-In Plug, part # LHCS102-SI60C
4.25" Pilot Hole, Lionshead Trailer Wheel Center Cap w/ Snap-In Plug, part # LHCS108-SI60C
4.88" - 4.9" Pilot Hole, Lionshead Trailer Wheel Center Cap w/ Snap-In Plug, part # LHCS109-SI60C
I have included product description links and a video review link below.
view full answer...
The Replacement Center Cap for 13" and 14" Aluminum Hi-Spec Series 06 Wheels part # AM54FR is specific to the Aluminum Hi-Spec Series 06 Trailer Wheel part # AM22328BP or part # AM20281B. If these are the wheels on your trailer then the center caps will fit. view full answer...
If your 16" wheels are 6-lug Viking series wheels with the 4.25" diameter pilot hole, the Replacement Center Cap for 15" or 16" Aluminum Viking Series Wheels - Chrome, part # TA65FR, will fit your wheel. If the pilot hole is not 4.25" or you do not have Viking series wheels, I can provide you will a center cap that will fit. I will need the measurements of the pilot hole.
I have included a demo video link below. view full answer...
The Americana Trailer Wheel Center Cap # AM90156C will work for your application and does include the center cap (plug) for the wheel cap. 4-7/8" translates to 4.875" as a decimal. Your 16", 8 lug rims with pilot hole of 4-7/8" will work just fine with the Americana Trailer Wheel Center Cap # AM90156C. view full answer...
As long as your wheels are 16 inch in diameter with an 8 lug bolt pattern and have hand holes the Wheel Masters Wheel Covers # WM3160B0 that you referenced are going to fit and work great. These will hold up really well too. view full answer...
In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. I attached an FAQ article on determining bolt pattern for you to check out. Most likely you have a 5 on 4-1/2 inch bolt pattern but it doesn't hurt to double check.
Next thing you will need to know is what spindle you have on your trailer.... view full answer...
The Replacement Center Cap for 16" Aluminum Viking Series Wheels # CXF105B will fit a 16" diameter, 8-lug wheel with a 4.9" pilot hole. It was just designed around the 16" Aluminum Viking Series Wheels like what comes with the combo kit # A16RG8BMMFL which it is titled this way. view full answer...
While it is true that the Americana Trailer Wheel Center Cap # AM90092 does have that center plug, this center cap is only available as a kit so to replace the center plug you'll need a whole new cap. I confirmed this with my contact at Americana. view full answer...
Your 2020 Gulf Stream Vintage Cruiser 19ERD has 14" 5 lug conventional wheels, and will need the Americana Baby Moon Trailer Wheel Center Cap # AM90086. view full answer...
The stud doesn't matter when it comes to the wheel cap, you just need to measure the width of the lug nut to ensure the Phoenix USA Rear Hub Cover w/ Pop Out # PXQ822R or Phoenix USA Rear Hub Cover w/ Pop Out # PXQ820R will fit the lug nut.
The # PXQ822R is going to fit 33mm lug nuts and the # PXQ820R is going to fit 30mm lug nuts.
view full answer...
After taking a look at your pictures you need a center cap plug. Unfortunately we do not have a center cap plug with the dimensions you need for your wheel. Another option would be to remove your wheel and pop out the center cap and measure the pilot hole of your wheel. Once you have that measurement you can check our inventory, with the weblink I have included below, to find a wheel center cap. For example, if your Wells Cargo trailer's wheel has a pilot hole that measures 3.33", you could... view full answer...
The Phoenix USA Wheel Center Cap part # PXQ2010 has right hand threads (threads run clockwise) but that does not mean there is a left and right hand cap. You will need to check the bracket of your existing cap to see if there is a L at the end of number on the bracket. If there is a L then you will need a left hand thread. This is common on Freightliners. If you do not have the L for "left hand thread" you can use the PXQ2010.
The cap installs with the included bracket on the axle plate,... view full answer...
To replace the missing lug nut covers on your Namsco Wheel Cover # NA7160B1 you'll need the Lug Nut Covers for Wheel Masters and Namsco Wheel Covers # WM9003-4. These covers will just snap into place give your Namsco wheel covers a finished look. view full answer...
When measuring your existing wheel to see if the Americana Baby Moon Center Cap # AM90086 will fit, you will want to measure the outer diameter of the inner ring, along with the outer diameter of the inner ring with one of the tabs (see attached image for clarification). You will also just need to verify the wheel's overall diameter and the number of bolt holes.
The Baby Moon Cap # AM90086 is designed to fit 13 inch, 14 inch, and 15 inch 5-lug conventional wheels. In order for this... view full answer...
Yes the Baby Moon Cover part # AM90086 that you referenced is a fit for the Dexstar conventional style wheel you send in a picture of. I was able to verify this by looking at the sticker in your picture. view full answer...
The Lionshead Trailer Wheel Center Cap # LHCS102-SI60C fits a 3.19 pilot hole diameter on your wheel. The overall height of the center cap is 3-1/2" and the center hole is 2" in diameter. I am not sure if it will fit over your UPF Vault 1.98 axle caps but you should be able to determine a fit with the dimensions I gave you. view full answer...
The Wheel Masters Lug Nut Covers - Stainless Steel - 1-1/2" # WM8012 that you were looking at are the closest we have to what you are looking for. These are made to fit over 1-1/2" lug nuts, so you can measure your lug nuts to verify if they are 1-1/2". Also, the height of this lug nut cover is 1-3/4" so if you measure again maybe your lug covers are actually about 1-3/4" as well. view full answer...
The Americana Baby Moon Trailer Wheel Center Cap # AM90086 referenced in your question is designed for 13 inch, 14 inch and 15 inch conventional trailer wheels with 5 lugs. In order to determine if these will fit the wheels on your 2016 Retro Riverside Whitewater Trailer, you will just need to take a couple measurements.
You will need to measure the outer diameter of the inner ring, along with the outer diameter of the inner ring with one of the tabs. I have attached an image that clarifies... view full answer...
We have one baby moon wheel cover for a 15 inch wheel with 6 lugs. For that we have the part # AM981306. It measures 10-9/16 inches overall and has an inside diameter of 10-1/4 inches.
I attached a review video for this cap for you to check out as well. view full answer...
We do have a few options for you, the Americana Trailer Wheel Center Cap # AM90098 will fit on 14" diameter wheels with a 5 bolt pattern; and the Replacement Center Cap for 13" and 14" Aluminum Hi-Spec Series 06 Wheels # AM54FR which will fit on 13" and 14" diameter wheels.
I recommend you measure the wheels pilot diameter and verify that it matches the pilot diameter of these caps which are 3.19". view full answer...
We have one potential option for your 15 inch wheels, though they do have an inside diameter of 10-1/4 inches, which is close enough to 10-3/8 inches that I did want to at least mention it in case you just want to verify your measurement. The option that may work for you is the Americana Pointed Top Baby Moon Trailer Wheel Center Cap # AM981306.
This cap will fit 15 inch, 6-lug wheels and have the inside diameter I mentioned of 10-1/4 inches, which is important as they are a snap-in... view full answer...
With the plug removed, the hole in the end of the Lion's Head # LHCS102 center cap measures 2 inches in diameter as shown in the provided photo. It's possible that your bearing buddy might be compatible, but the opening in the center cap is designed to allow access to the grease zerks of E-Z lube spindles. view full answer...
I looked up the lug nut size of the 2005 Workhorse W22 chassis that you have and since it has 33 mm lug nuts the lug covers you'd need are the part # PXSP33. We don't have this size lug nut though. view full answer...
You can use the Phoenix USA QuickTrim Hub Cover # QT545C with the HWT Aluminum Hi-Spec Series S5 Trailer Wheel # AM22323HWTB.
This hub cover is designed to snap onto wheels that have a 5 on 4-1/2" bolt pattern and 1/2" lug nuts, both of which the HWT wheel uses.
I have added links to video reviews of the wheel and hub cover for you to take a look at. view full answer...
Based on your photo, it looks like you have something like the Phoenix USA Rear Hub Cover w/ Pop Out - 8 on 275mm - 33mm Lug Nuts - ABS Plastic # PXQ822R which includes screw-on lug nut covers. There are not any replacement screw-on lug nut covers for this set so you may need to buy the whole kit in order to get those covers.
Keep in mind, these are a fit for 33mm lug nuts; my research tells me that your Kodiak 4500 may have 30mm lug nuts so you will want to measure to verify. We do... view full answer...
I spoke to my contact at Phoenix USA and he told me the correct part for your 2007 Winnebago Tour 40TD Motorhome is the Replacement Right Thread Mounting Bracket for Phoenix USA Wheel Center Caps for 8-1/4" Axles # PHX67FR. view full answer...
Yes, baby moon hub cap # AM90086 will fit Dexstar Conventional Steel Wheel # AM20514. This particular baby moon fits 13, 14, and 15 inch conventional steel wheels. I have linked a video featuring the baby moon hub cap for you. view full answer...
The Wheel Masters Lug Nut Covers # WM8011 that you referenced do fit the size lugs you mentioned of 1-1/16" which is commonly found on Ford RVs like your 1997 Ford E-350 Class C so it will fit but they are all press-on style covers. There aren't two of these that would screw on. We do not have a setup like that available. view full answer...
The HWT Center Cap CAP14AL06S that you referenced is no longer produced by the manufacturer but we do have the very similar Americana # AM90098 for 14" wheels with 5 bolt patterns or # AM90091 for 15" wheels with 5 bolt patterns. Both of these are designed for 3.19" pilot hole diameters, so you may just want to verify this matches the existing pilot hole on your wheels to ensure fitment.
These caps features a really sleek chrome over plastic construction that is completely rust resistant.... view full answer...
You need to measure the center hole of the wheel you have and then check out the link I attached which has all of the trailer wheel center caps we offer. You will need to select the center hole diameter that you have that matches the pilot size filter sizes. That will be the cap you will need. We do have a few plastic ones but most are metel.
The cap fits through the hole and then the flange behind it holds it in place to the hub of the axle. view full answer...
I spoke with my contact at Americana and they told me that the Americana Trailer Wheel Center Cap, part # AM90091, will fit all 15 inch wheels regardless of the lug bolts, as long as the pilot hole is 3.19 inches diameter. view full answer...
I recommend replacing your wheel center caps with the Lionshead Trailer Wheel Center Cap w/ Snap-In Plug # LHCS109-SI60C as the largest replacement plug I can find is the Plug # CCP-60C which only has an outside diameter of 2-3/16".
The new Lionshead cap uses the more common Plug # LHSI60C which has an outer diameter of 2" and we have several of available. view full answer...
The pilot hole on a wheel is the big center hole right in the middle of the wheel. It fits over the hub.. It can be tough to measure these with the wheel still on the trailer so you will want to remove the wheel and then it will be easier to measure. The best way to measure it would be to use digital or dial calipers.
I can look up the tire you previously ordered, # AM10256, but since the wheels that the tire fits could have different size pilot holes I cannot go by the tire size alone.... view full answer...
The baby moon covers part # AM90086 that you referenced are what you need. We had a customer with basically the same trailer as yours send in a picture confirming these fit for their 2018 Vintage Cruiser. I attached a picture for you to check out as well. view full answer...
The Replacement Center Cap for 15" Aluminum Hi-Spec Series 06 Wheels is # AM90091B or # AM90091 both of which are confirmed to fit your wheels.
The 3.19 is the diameter of the pilot hole on the wheel itself were it fits over the hub for future reference. view full answer...
The Americana Trailer Wheel Center Cap Item # AM90195 can get a little water inside but, when the wheel is tightened against the hub, it seals fairly well, the water entry should be minimal, and should drain back out. The plug can be removed fairly easily if you wanted to rinse the inside of cap.
An idea that may help keep any water out is to add a small piece of a foam tape around the edge before placing it on the hub. As the wheel is tightened down the tape will seal and gaps between... view full answer...
Based on my research, your Dexstar model WS512DEX features a 6 on 5-1/2 inch bolt pattern and uses a 4.25 inch center cap size.
With this in mind, I recommend the Lionshead Trailer Wheel Center Cap # LHCS108-SI60C. This stainless steel cap is resistant to corrosion and features a removable snap-in plug that will provide easy access for hub maintenance on E-Z Lube axles. I have attached a short video demonstration on this cap that you can check out, along with a link that will take you... view full answer...
I cannot find any baby moon hub caps for your 13" wheels. The ones that I do see, the wheels have 3 bump outs on the wheel themselves that I do not see on your wheel. These bump outs are needed to hold the baby moon hub cap in place. You can see them on the Dexstar Conventional Steel Wheel # AM20214.
They also specify that the Baby Moon Trailer Wheel Center Cap # AM90086 will only work on a 5 lug wheel and I do not see one for a 4-lug option so this may be something that is not built... view full answer...
For your 15 inch wheels, we have the Americana Trailer Wheel Center Cap - Chrome - 3.19" Pilot - 15" Wheels # AM90091. These are the only options we have available for your wires with the hole to mount inside the triangle design. view full answer...
We don't have anything quite like what you are describing for 16 inch wheels, but we do have some very similar options. We have the Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel # AM90086 which are 9-1/4 inches inside edge to inside edge. These are a confirmed fit for the 13-15 inch conventional wheels.
If you were able to move down to a 15 inch wheel, we have two options:
Karrier ST205/75R15 Radial Trailer Tire w 15" Wheel with +.5 Offset - 5 on 4-1/2 - Load... view full answer...
The Lionshead Trailer Wheel Center Cap w/ Snap-In Plug part # LHCS102-SI60C is 3.5" deep. This can then be used to determine compatibility with a buddy bearing. view full answer...
In order to determine what size replacement center caps will fit your RV travel trailer, you will need to measure the pilot hole diameter on your wheels. For example, if your pilot size is 3.19 inches, you could go with part # 319EZ or for a 4.25 inch pilot size you would need part # 425EZ. I am including a link to all of the center caps that we offer. Just use the filters on the page to narrow down the search. view full answer...
We have two options for trailer wheel center caps that fit pilot holes with a diameter of just over 5 inches, which I'll list for you:
- 5.12" Pilot Diameter: Americana Trailer Wheel Center Cap - 5.12" - Chrome # AM90083
- 5.15" Pilot Diameter: Americana Trailer Wheel Center Cap - 5.15" Pilot - Stainless Steel # AM90078
As you can see these are both similar sizes so you will want to be sure of your exact pilot hole diameter before choosing. view full answer...
It definitely sounds like you are needing something like Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Right Thread # PXQ2020XL. Just a few things to check to confirm fitment, this fits 10 lug on 285mm pattern and fits 8-1/4" hubs. It includes the small cover with the bolt in it and also the mounting bracket with the two mounting holes like you mentioned. This closely matches what you have described, but just to be sure I would measure to verify your setup... view full answer...
The R-Pod Hood River Edition came with ST235/75R15 tires and the closest thing we have is the 225/75R15 tires which will use the same wheels and have the same pilot diameter of 3.19 inches.
The Trailer Wheel Center Cap, Stainless Steel, 3.19" Pilot Size # LHCS102-SI60C will be the correct size and is my recommendation. I've attached a couple videos to assist. view full answer...
Based on the dimensions you mentioned needing for a baby moon cover the # AM90086 that you referenced would be the correct fit. I attached a review video for more info on it as well. view full answer...
To measure the pilot hole on your wheel, you will need to remove the cap in the picture and then measure the inside diameter of the hole in the wheel. Most wheels with the bolt pattern you have in the photo are 4.88 inches or 4.9 inches with a select few at 4.76 inches.
I recommend the Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 4.88" to 4.9" Pilot - Stainless # LHCS109-SI60C if you have one of those options, but we don't have a center cap compatible with the 4.76 inch option... view full answer...
I first recommend taking a quick measurement on your trailer to ensure that the Trailer Wheel Center Cap # 319EZ will fit over your existing Bearing Buddies. The inner depth of the center cap is 3-1/8 inches to the tabs on the removable plug on the end of the cap. You will want to measure the length of the trailer's spindle that sticks through the center hole of your wheel, from the face of the wheel to the end of the Bearing Buddy cap. If it measures less than 3-1/8 inches, then you can... view full answer...
The Americana Trailer Wheel Center Caps that you referenced are designed to fit either 15 inch or 16 HWT trailer wheels. If you have a 15 Inch HWT wheel, such as # AM20455B, the center cap you will want is # AM90091B.
If you do not have an HWT 15 inch trailer wheel, this cap will not notch into place correctly. We do offer other hub covers that will protect your wheel's lug nuts, such as the Phoenix USA QuickTrim Hub Cover, Black # QT655B or in Chrome # QT655C. This hub cover is designed... view full answer...
I would be happy to help, but when I looked up your 2017 Gulf Stream Vintage Cruiser I was unable to confirm the wheel size.
The Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel # AM90086 you were looking at fit 13" - 15" convetional trailer wheels so if your wheel size is one of these sizes this would be a great option.
If you find you have a different wheel size just let me know.
I included a video of the # AM90086 for you to take a look at. view full answer...
I would be happy to help you find the correct lug nut covers for your 2006 Winnebago Sightseer built on the Workhorse chassis, but unfortunately we do not have a breakdown of the specific components your motorhome was outfitted with.
Instead you will need to measure your lug nuts, or find the size of the socket used to remove the lug nuts.
The Wheel Masters Lug Nut Covers - Stainless Steel - 1-1/2" - Qty 6 # WM8012 you were looking at were designed to fit 1-1/2" lug nuts, so if that... view full answer...
I have attached our 14" diameter trailer wheels for you. In order to determine the correct center cap I would need you to try and find your wheels below or send me a photo. Once done so I can see if we have options for you. view full answer...
We have a baby moon center cap that is designed for a 15 inch 6 lug wheel like what you have that is part # AM981306 but you'd want to still measure your wheel to determine if it will fit.
This has an overall diameter of 10-9/16 inch and an inside diameter of 10-1/4 inch. view full answer...
The Americana Baby Moon Trailer Wheel Center Cap # AM90086 is intended for 13-, 14- and 15-inch conventional steel trailer wheels like # AM20504 that have three projections around their center, as shown in the linked photo. The cover's inside diameter of 9-1/4-inches matches up to the outsides of these projections for a snug snap-on fit.
The cover will not work on spoke wheels with triangular cutouts like Dexstar Steel 8-Spoke Trailer Wheel # AM20522. view full answer...
The replacement cap that will fit your size 14 wheels is the Americana Trailer wheel Center Cap # AM90098.
This cap has a chrome over plastic finish, measures 3.19 inches in diameter and is made for a size 14 wheel with a 5-hole bolt pattern. view full answer...
We do have the stainless steel Americana Trailer Wheel Center Cap # AM90175 which fits a 3.19" pilot and has an overall height of 3-3/4".
I went out to the warehouse and found that the internal height is about 3-1/8" to clips on the plastic piece but then about 3-1/2" without the plastic piece in place.
Attached is a review video for you to check out. view full answer...
The Americana Trailer Wheel Center Cap - Chrome # AM90091 is designed to fit 15 inch diameter wheels like # AM20455 that have a 5-hole bolt pattern and 3.19 inch pilot diameter. If this matches the wheels you have on your 2008 Starcraft Trailer, then this will work great.
I have attached a video demonstration on this product so you can see exactly how it looks.
I recommend measuring the pilot diameter of the wheels on your trailer to ensure that this will fit. I have also attached... view full answer...
We carry two baby moon center caps; part # AM90086 is the standard look and part # AM981306 has a more unique pointed style to it. When choosing a baby moon center cap you need to match them up to the bolt pattern of your trailer's wheels. The standard cap fits 5-lug 13, 14, and 15 inch wheels and the pointed style fits 6-lug 15 inch wheels.
So for your trailer we have part # AM90086 that fits your 14 inch rims as long as you have a 5-lug bolt pattern. view full answer...