Could 24x60 etrailer Cargo Carrier for RV Bumper # e99049 Install Without Clearance

Question

Question:

I haven’t enough clearance between my bumper and my RV to install ? Any ideas

asked by: Hubert T

0

Expert Reply:

Do you have any pictures of the setup? Without clearance I would say there isn't a way to install the 24x60 etrailer Cargo Carrier for RV Bumper # e99049 but maybe there's a different way to look at it.

expert reply by: Jameson C

0

Jameson C.

9/8/2025

Hey, did you have a chance to find the pictures I asked for? If you’re still looking for a solution, I’m happy to help.

Answer 1

Hey Bryce, thanks for reaching out, and good question. The Mount-n-Lock Heavy-Haul’r Heavy Duty 4-inch #MNT43VR is basically the same 4" x 4" bumper as the standard 4.0, but with a stronger mounting setup. You’re not getting a bigger or…

view full answer...

Answer 2

The 24x84 etrailer Cargo Carrier for RV Bumper part #e96ZR can hold a spare tire but there isn't any sort of specific mount for this. The photo attached below is a custom job from a neighbor and I'm not totally sure what they used to create…

view full answer...

Answer 3

Hey Dave, are you possibly looking for an RV sewer hose carrier like the part #A04-5094BK which would attach to the bottom of your bumper and give you a way to store the hose or are you looking for like a cargo carrier that attaches to an RV bumper…

view full answer...

Answer 4

I do have an option for you but there isn't a spare tire holder designed to be used with the 24x60 etrailer Cargo Carrier for RV Bumper part #e99049. That said, you might be able to use something like the CE Smith Spare Tire Carrier for Trailers…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Since your trailer is sitting perfectly level, even though it is on an incline, the tongue weight of the setup will be accurate if you were to weight it as-is. If the nose of the trailer was high or low the figures would get skewed. You will need to…

view full answer...