What Air Lift Air Bags do I Need for My 2017 Toyota Tacoma with Lift Blocks, and Air Compressor?

Question

Question:

Need an air lift kit for a 2017 Toyota Tacoma, 4 wheel drive.. Would prefer the Air Lift brand if possible. The Tacoma has a block style lift kit installed on the rear leaf springs. I tried using your online deal but got a message that it was not working correctly. THANKS

asked by: Mike E

0

Expert Reply:

Hello again Mike,

Happy to get you into the right Air Lift set-up for your 2017 Toyota Tacoma.

You will need the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle # AL49DQ for the airbag kit.

Not all lift kits provide the same amount of lift, so you’ll either need to reach out to the manufacturer of your rear lift blocks to confirm how much they increased the distance between the frame and axle, or you can measure this yourself. The # AL49DQ brackets are designed for a stock distance of 5 1/2", so if your measurement is at least 7 1/2", you’ll need the 2" spacer # AL52420. I’ve attached a measurement guide directly from Air Lift’s website that you can use for reference.

* If you do measure, make sure the truck is unloaded and parked on level ground.

If you're looking for a great air compressor to pair with it, I recommend the Air Lift WirelessAIR Compressor System for Air Helper Springs # AL74000EZ. I really like this system because it comes with both a remote and Bluetooth compatibility, making it super easy to use, don't even need to leave the cab of your truck.

What kind of blocks did you have installed? Do you have a company or part number?

expert reply by: Kate F

0

Airlift How to Measure for Spacer
(click to enlarge)

Mike E.

6/12/2025

Kate the lift kit is made by Torch and the lift on the rear according to them is 2” if it helps I can send a jpeg of the specs

Kate F.

6/12/2025

@MikeE I would go ahead and order the spacers, if you end up not needing them just let me know and I will get you taken care of. The 2" lift is kind of a gray area, sometime you need them, sometimes you don't.

Mike E.

6/12/2025

@KateF I’m a little confused at this point in time I apologize. I’m 67 and 2 years ago I installed this kit myself, so what you’re saying is I might have to remove the tapered 2” blocks that I installed with the lift kit and install a different set of spacers is that correct. If so does your company offer said spacers, maybe you can supply a link to that product as well.. I’m very active and looking forward to installing your air bags to get my cargo trailer level. Thanks for your help Kate

Kate F.

6/12/2025

@MikeE Happy to clarify, Mike. You will not need to remove the 2" blocks that you installed with your lift kit. You’ll want to install the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle # AL49DQ, and because of the lift kit on your Tacoma, you may also need to install the Air Lift 2" spacers # AL52420. These spacers help fill the added gap between the axle and the frame that results from your lift. Since a lifted truck increases the frame-to-axle distance beyond what the air springs are designed for at stock height, the spacers ensure the air bags perform properly and aren’t overextended. I attached a video as well where Jeff explains what the spacers are for. If you have any other questions, please ask away. That is what I am here for =)

Helpful Links

tv-demo-air-lift-vehicle-suspension-al52420.aspx

Answer 1

Since you have a 2 inch lift in the rear of your 2005 Toyota Tacoma you would also need the spacer kit part #AL52420 with the Air Lift Load Lifter 5000 kit part #AL49DQ that fits your truck.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...