What Size Valve Stem Does The Rim AM92NR Require?

Question

Question:

WHAT SIZE VALVE STEM IS REQUIRED FOR THIS RIM?

asked by: GEORGE C

0

Expert Reply:

Hey George,

The Americana wheel, # AM92NR, requires a 0.625" or 5/8" valve stem like part # AM20907. That is a standard size throughout 17-1/2" rims.

Do the rims you are replacing have an offset like this one?

expert reply by: Nick S

0

Nick S.

9/8/2025

Hey George, did you find the right valve stem for your rims? I'm asking because knowing your outcome could help others with similar rim replacements.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 3

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 11

Hey Clarence. There's no way to look at a tire or wheel and tell if it's a 5 on 4-1/2 or a 5 on 5 but you can take a real quick measurement to figure it out. If you'll look at the picture below you'll see a wheel with a red line on…

view full answer...

Answer 12

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

What Size Valve Stem Does The Rim AM92NR Require?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching