Can 80 Amp Converter/Charger 9380 be Used in Place of 9180A

Question

Question:

I have a 9180A converter charger that has gone bad. I was wondering if i replace it with a 9380A are there any modification to the current plugs or wiring.

asked by: Cary C

0

Expert Reply:

Hey Cary, yes you can use the 9380 part # PD89RR in place of the 9180A and it will work great. They are both 80 amp converter chargers so you wouldn't need to make any modifications.

expert reply by: Jameson C

0

Jameson C.

9/12/2025

Hey Cary, did the 9380A converter charger work out for you without needing any modifications? I'm asking because your experience could help others in a similar situation.

Answer 1

Yes, the Redarc 12V Smart Battery Monitor #RED42RR will work with your 450 Ah setup from your four 6V batteries. I have attached a wiring diagram below for your reference.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Can 80 Amp Converter/Charger 9380 be Used in Place of 9180A

Product Page this Question was Asked From

Continue Researching