Which MORryde X-Factor Can be Used with CRE3000 MORryde Equalizer Kit 2022 Grand Design Imagine

Question

Question:

I have a 2022 GD Imagine 17MKE travel trailer. I upgraded to the CRE 3000. Interested in the XFactor Crossmember. How many will I need and which one do I get?

asked by: Darla M

0

Expert Reply:

Hey Darla, the correct MORryde X-factor for trailers that have a MORryde CRE3000 kit installed is the standard kit part # MR33WR.

Running three of these would give you the most stable setup so that would be what I would recommend.

expert reply by: Jameson C

0

Darla M.

5/21/2025

If only installing 2 crossmembers, what locations are best to use?

Jameson C.

5/21/2025

@DarlaM The front and rear hangers. You'd want to leave off the center if only doing two.

Darla M.

5/21/2025

@JamesonC Thank you so much for your help, much appreciated.

Jameson C.

5/21/2025

@DarlaM Glad to help!

Answer 1

Hey Ronnie! You want the upgraded equalizer to match the existing equalizer measurements so you don't throw off the suspension geometry. The Road Armor #LC53CK is only 6" long making it is a little too short for your setup. The MORryde Shock…

view full answer...

Answer 2

You sure do Greg! Which is why the MORryde X-Factor Crossmember for Standard Frame Hangers item #MR33WR comes with longer suspension bolts. These bolts will replace the ones currently being used on your trailer's spring hangers. The X-Factor…

view full answer...

Answer 3

Hey John! With the CRE3000 on your Reflection you need the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR. The same crossmember will be used on all three sets of hangers. The one thing I would do is take a look under your trailer to…

view full answer...

Answer 4

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 5

Hey Chuck, so there are some varying opinions on where to put the X-Factor crossmembers if you are only going to use two on a tandem setup. There's no exactly right or wrong answer but I believe the best case can be made for using the center…

view full answer...

Answer 6

Those are some good options, and the best overall upgrade (without getting too crazy like you said!) for your Jayco with tandem 3,500 lb axles is going to be the MORryde CRE3000 with the X-factor crossmember. The Road Armor is good, but the…

view full answer...

Answer 7

Hey Lester. The 2016 Grand Design Reflection 337RLS uses a Schwintek system. The motor should be located at the top of the vertical column on either side of the slide-out, which is accessible from the outside. You'll need to pull back the rubber…

view full answer...

Answer 8

Hello Lanny, thanks for reaching out. The CRE 3000 is already a pretty good suspension system, but if you want to upgrade, the first thing that comes to mind are the AllTrek 4000 equalizers. They have more rubber than the CRE 3000, 40% more, so you…

view full answer...

Answer 9

Hit the little gray x to the left of where it has the vehicle info listed and you can select a new vehicle. Or hit the change vehicle button to the right. Maybe you tried those already though and it wasn't working? Does you 2025 Silverado have…

view full answer...

Answer 10

Hello Jacques, thanks for reaching out. Yes, you can put just one MORryde X-Factor Crossmember #MR33WR on the center hanger for starter. MORryde does recommend doing all 3 for optimal support, but it is perfectly acceptable to start with just one as…

view full answer...

Answer 11

Hey, Chris. After doing some research and checking with Lippert, It looks like the only replacement part they have for the Venture Actuator and High Speed Slide-Out Motor, part #LC168956 is the motor itself, part #LC295380. In my searching It looks…

view full answer...

Answer 12

There is likely a suspension upgrade that will work for you, but you'll need to find a kit that has equalizers which are the same measurements as yours, and fit within your axle capacity. For example, the Road Armor Shock Absorbing Equalizer Kit…

view full answer...

Which MORryde X-Factor Can be Used with CRE3000 MORryde Equalizer Kit 2022 Grand Design Imagine

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching