When Adjusting the Bunks on an EZ Loader Trailer Do I Want the Bunk Brackets Loose?
Updated 10/27/2025 | Published 03/15/2025
Question:
Good afternoon. I own an EZ LOADER trailer for an 18 Key West 179 FS. I believe the model is 16-18 BT. Could you please give me a advice? When adjusting the bunks, do I leave the swivel part of the bunk brackets a little loose so that bunks can move laterally as the boat is being loaded, or should they be tightened completely to prevent movement? Thank you for any help.
asked by: William A
Helpful Expert Reply:
Hey there Bill,
When adjusting the bunks on your EZ Loader trailer, tighten the swivel brackets securely but not excessively. They should allow slight movement to self-adjust as the boat loads, ensuring even contact with the hull. However, they shouldn't be so loose that the bunks shift significantly. A little flexibility helps with proper alignment, but excessive movement can cause instability. After loading the boat, check that it sits evenly without undue pressure points and make adjustments as needed.
When is the next time you will be getting out on the water?
Product Page this Question was Asked From
Roadmaster Rollaway Trailer Hitch Protector
- RV Skid Wheels
- Hitch Mount
- Bolt-On
- Roadmaster
more information >
Continue Researching
- Search Results: boat trailer parts
- Search Results: bow roller
- Video: Complete Breakdown of the Yates Bow Roller for Boat Trailers
- Video: Checking Out the Bow Roller Assembly w/ Bells for 4" Wide Bracket
- Video: Let’s Check Out the CE Smith Bow Roller Assembly with Bells for 4" Wide Bracket
- Video: The Low-Down on the CE Smith Bow Roller Assembly with Bells for 4" Wide Bracket
- Video: Ultimate Overview of the Bow Roller Assembly w/ Bells for 4" Wide Bracket
- Shop: Yates Bow Roller for Boat Trailers - TPR - 4" Long - 1/2" Shaft - Yellow
- Shop: Yates Endcap for Boat Trailer Rollers - TPR - 1/2" Shaft - Qty 1
- Shop: CE Smith Bow Roller Assembly with Bells for 3" Wide Bracket - PVC - 1/2" Shaft - Amber
- Shop: CE Smith Bow Roller Assembly with Bells for 4" Wide Bracket - PVC - 1/2" Shaft - Amber
- Shop: Bow Roller Assembly w/ Bells for 4" Wide Bracket - TPR - 1/2" Shaft - Yellow
- Shop: Trailer Square U-Bolts (Qty 2), 2-1/8" x 4" x 7/16"
- Shop: Replacement Nut for Trailer Suspension U-Bolts - 1/2" Diameter - Galvanized
- Article: Determining Trailer Tongue Weight
- Q&A: Swing-Away 2-Inch Drum Brake Actuator Coupler to Replace Discontinued Fulton A60
- Q&A: How Much Wall Clearance Does Thomas Payne Dual Reclining RV Loveseat # TP68KR Require
- Q&A: Flat Tow Set up for a 2023 Ford F-250
- Q&A: Roadmaster Rollaway Trailer Hitch Protector With Hitch That Has Chain Tabs Below Receiver
- Q&A: Could Gen-Y Nomad Fit on 2021 Chaparral Lite 30BHS
- Q&A: What Are the Frame Tabs Called That a 5th Wheel Pin Box Mount to?
- Q&A: What is the Best Hitch for a 2024 Toyota Sienna?
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Measure for Trailer Hitch Drop
- Article: Rust Prevention
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Article: The Best Trailer Tongue Locks for Preventing Trailer Theft
- Article: Can You Flat Tow a Ford Bronco?
Kate F.
10/27/2025
Hey Bill, how did the bunk adjustment on your EZ Loader trailer turn out? Did the slight flexibility in the swivel brackets help the boat sit more evenly on the bunks? Your update could make it easier for others working on similar trailer setups.