What Kind of Chassis is My 2009 Damon Avanti Built On & What Suspension Enhancement do You Carry?

Question

Question:

Will the air Lift Load Lifter 5000 air spring work on a 2009 Damon Avanti chassis? It is not one of the model choices and I cannot find the exact chassis number for the Avanti. Thanks

asked by: Glenn B

0

Expert Reply:

Hello Glenn.

In my research I have found that the 2009 Damon Avanti is built on the Workhorse W16 chassis. The Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle # AL88202 are for the Workhorse chassis but only the W20, W22, and W24. The only suspension enhancement that we have for the W16 chassis is the Air Lift 1000 Air Helper Springs for Coil Springs - Front # AL81560. I know it's not the beefy bags you were looking at, but you will definitely notice a difference. I have attached a couple of videos for you to check out as well.

What kind of issue are you having that you are looking into the airbags?

expert reply by: Kate F

0

Glenn

2/3/2025

Hi Kate The Avanti is a lightweight A class and feels like it’s going to tip over sometimes! I was looking to stiffen it up. The Al1560 sounds good for the front. You also sent installation instructions for Al 88202, do they fit on the rear? I have no experience with these and wondering if just the front is a good start. When I used the number link in your message on the Al1560 it said they would not fit the Damon? It said I need some $800 Sumo’s? Not sure what I am doing.

Kate F.

2/3/2025

@Glenn The joys of trying to drive a camper with body roll, it gives you that sick feeling in your stomach like your first roller coaster as a kid but without the fun part! Now knowing what the real issue is I have some different options for you that are going to make your driving experience more enjoyable. I would start with the Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets for Class A Motorhomes # RM25RR, you will notice a huge difference as it has a special gas spring that pushes back when your RV starts to wander, so you don’t have to fight the steering wheel as much. This makes driving easier, safer, and less tiring. Another upgrade you can make to that will help a lot is going to be your sway bars. For the rear you will want Roadmaster Rear Anti-Sway Bar - 1-1/2" Diameter # RM-1259-118, and for the front Roadmaster Front Anti-Sway Bar - 1-5/8" Diameter # RM-1259-115, or if you wanted to spend a little more on the front and get the kit with the TruTrac # RM-1259-116 it will help even more as the TruTrac rod is will help keep your axle in line preventing even more wander. By installing these components you will notice a huge difference. I attached some review videos for you to take a look at. We take a lot of pride in our content and I think our videos give you a good feel for the products before purchasing. If you have any questions at all, please ask away.

Helpful Links

tv-manufacturer-review-roadmaster-anti-sway-suspension.aspx

tv-review-roadmaster-rear-anti-sway-bar-rm-1139-149.aspx

Answer 1

Hey Craig, Sure thing, and there is one option for air bags for your 2006 Fleetwood Bounder 36Z on a Workhorse chassis, which is the following from Air Lift: - Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88202 You made a great choice…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

What Kind of Chassis is My 2009 Damon Avanti Built On & What Suspension Enhancement do You Carry?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching