What Gauge Wire Should Be Used For Optronics STL17RB And STL16RB Tail Lights?
Updated 11/03/2025 | Published 01/16/2025
Products Featured in This Question
Question:
I have a 18 foot trailer that I am installing 2 rear led lights part numbers STL17RB and STL16RB and 5 led side marker lights part number C525A and 4 led side marker lights part number C525A. My question is what gauge wire should I use for installation. Also I am running new wire to the electric brakes that use magnet part number AKBRKR-M12 on 4 wheels what gauge wire should I use ? Thanks
asked by: Terry
Expert Reply:
Hey Terry, thanks for reaching out. For the Optronics # STL17RB and # STL16RB tail lights 16 gauge wire is what I would use. For the brakes you will want to use at least 12 gauge wire. If it is a shorter trailer you can get away with 12 gauge, for longer trailers say 20' or longer you may want to up that to 10-gauge. We sell this wire by the foot if you need some. Take a look at the following:
- Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot # 10-2-1
- Jacketed 2 Wire (Brake Wire) - 12 Gauge - per Foot # 12-2-1
- Deka Wire - Jacketed 4-Wire - 16/4 Gauge - per Foot # DW03240-1
I hope this helps and let me know if you need anything else.
Product Page this Question was Asked From
LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - 22 Diodes - Driver Side
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- License Plate
- Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 8-1/16L x 2-7/8W Inch
- Red
- Optronics
more information >
Continue Researching
- Search Results: 25580
- Search Results: ramp spring
- Search Results: trailer lift supports
- Q&A: Does Trailer Lighting Ground Through the Hitch Ball
- Search Results: ring
- Shop: 16-Gauge Bonded 3 Wire - per foot
- Shop: 16 Gauge, 4 Conductor Bonded Parallel Wire - Per Foot
- Video: A Closer Look at the 16-Gauge Bonded 3 Wire
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer jack
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Ultimate Overview of the etrailer Enclosed Trailer Transition Plate
- Shop: Trailer Wiring
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer leaf springs
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Shop: Brake Controller
- Video: Checking Out the etrailer Enclosed Trailer Transition Plate
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Shop: Suspension Enhancement
- Article: Trailer Lighting Requirements
on Trailer Lights
Jesse M.
11/3/2025
Hey Terry, how did the wiring go for your trailer lights and brakes? I'm curious if the 16-gauge and 12-gauge wire setup worked well for your layout. Your update could make it easier for others working on similar trailer wiring.