How To Protect Your EcoHitch Hidden trailer Hitch Receiver From Rusting

Question

Question:

Greetings, How can I keep the EcoHitch Hidden Trailer Hitch Receiver 306-X7221 from rusting?

asked by: Dave N

0

Expert Reply:

Hey Dave,

You can protect your EcoHitch Hidden Trailer Hitch Receiver # 306-X7221 from rusting by spraying it off whenever road salt or chemicals kick up on it during the winter that could eat the paint. If you start to see any rust forming you can use a wire brush to clean it off and then repaint the hitch with some automotive grade black paint. If you live closer to the ocean the salt water can definitely expedite the paint's decomposition so you may need to look into another type of paint that better suits your climate.

expert reply by: Kevin C

0

Robin H.

12/15/2025

Hey Dave, how has your EcoHitch held up after following those cleaning and repainting steps? Knowing how well the paint protection worked could help others keep their hitches in good shape too.

Dave N.

12/15/2025

@RobinH Hi Robin, This year we used the Ecohitch maybe fifteen times to haul bikes. So far the original paint has held up! The pin hole location is kind of far back and sometimes means getting on hands and knees to install. Overall, very glad to have this on the LEAF.

Answer 1

We can help you install a 7-way and brake controller in your 2019 Kia Sorento but you do need to first start with a 4-way like the part #C56256 and then convert it to a 7-way with the part #ETBC7 so that you can install a brake controller like the…

view full answer...

Answer 2

The replacement you would need for your trailer axle that measures out to be 72 inches from hub face to hub face and is 60-1/2 inches from spring center to spring center you will need is The Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How To Protect Your EcoHitch Hidden trailer Hitch Receiver From Rusting

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching