Replacement 2,000 Pound Axle With 5 on 4-1/2 Bolt Pattern For Bear Trailer

Question

Question:

Needing a axle 72inch hub to hub 5 lug 4-1/2 bolt pattern 2000lb spring center is 60-1/2 inches on center didnt see one listed its for a bear trailer 2000 G3 BOAT

asked by: David C

0

Expert Reply:

The replacement you would need for your trailer axle that measures out to be 72 inches from hub face to hub face and is 60-1/2 inches from spring center to spring center you will need is The Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72 inch Long - 2,000 pounds # e32GR.

This axle is 72 inches long and has a spring center to spring center measurement of 58 inches. This will work for you but you will have to move the springs seats to align them with the leaf springs.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

While we do not have an axle which has the 60" spring center you are able to use the Dexter Trailer Axle #20545I-ST-72-15 and have 2 new Spring Seats #TRSS175 welded on. This will allow you to cut off the spring seats at a 58" spring center…

view full answer...

Answer 2

In order to mount the round 2,000 pound axle under your trailer's leaf springs, we will need to piece together an over-under kit for the 1-3/4 inch outer diameter of the axle. The Dexter Trailer Springs Over-Under Conversion Kits that you…

view full answer...

Answer 3

Safety chains come in a variety of classes: Class I (2,000 pounds gross trailer weight or GTW), Class II (3500 pounds GTW), Class III (5,000 pounds GTW), etc. It is important that the capacity of the chains exceed your GTW, the weight of the loaded…

view full answer...

Answer 4

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Michael, thanks for reaching out! The wheel is the same. The difference between the Kenda #AM32424 and the Kenda #KE94WV parts is the tire. The former is a standard Karrier tire while the latter is a Karrier KR53 which is supposed to be more of a…

view full answer...

Answer 7

Hey Dusty, I emailed the manufacturer to get the dimensions you are looking for on the #ABS56FR and the overall length is 5-5/32” with the hole spacing of 3-29/32” center to center.

view full answer...

Answer 8

Trailer or automotive wheels can have a positive or negative offset. The offset refers to the distance between the mounting surface of the wheel that touches the hub and the center line of the wheel, as shown in the diagram I have edited for you. A…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement 2,000 Pound Axle With 5 on 4-1/2 Bolt Pattern For Bear Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching