Replacement Parts Needed For The Thule DoubleTrack Pro XT Bike Rack

Question

Question:

I have a Thule double track pro 2 that is missing the plastic cover that allows you to lower and raise the rack. How can I get that piece.

asked by: Paul T

0

Expert Reply:

Hey Paul,

I've attached a parts diagram of the Thule DoubleTrack # TH92BJ. Are you needing just the covers (part 26) that go over the tilt latch or are you needing something else?

expert reply by: Kevin C

0

DoubleTrack Pin
(click to enlarge)

Doubletrack pin
(click to enlarge)

DoubleTrack Parts Diagram
(click to enlarge)

Paul T.

11/15/2024

I’m missing the circular insert of the part you sent me that allows you to push to raise or lower the main bar

Kevin C.

11/15/2024

@PaulT That part unfortunately is not a replaceable item since it's part of a larger assembly and Thule doesn't offer that assembly as a separate part. You can try giving them a call and seeing if they might have a damaged Doubletrack that you could take the assembly off of so that you can get your rack back in working order, otherwise you'll need to swap to a new rack altogether.

Paul T.

11/15/2024

@KevinC thanks for the info. Do you have any diy fixes? I’ve been using a divot fixer to manually do it. Any better options? Tx

Kevin C.

11/15/2024

@PaulT I actually own this bike rack so I went and grabbed it and took it apart. That light gray circle button that lets you raise or lower the frame post pulls on a spring-loaded pin that has a shear pin connecting it to the button. If your button is gone/broken/etc. you can use a split key ring to pull the spring-loaded pin out and allow the post to move. You can typically pick up a pack of split key rings at most hardware or department stores for about a buck. The key ring could also be attached something else that would give you a better grip to pull with if needed. It obviously won't be the prettiest but it'll make the rack functional again. I've attached some pictures of the pin I'm talking about above.

See All (4) Replies to Paul T. ∨

Answer 1

We do have a couple options for you that will work great depending on the bike rack you currently have. If you have the Thule DoubleTrack Pro 2 you can use the: -Replacement Rear Wheel Holder for Thule DoubleTrack Pro 2 #7524601001 & -Replacement…

view full answer...

Answer 2

For a replacement hitch pin for your Thule DoubleTrack Pro 2 TH9054, the part you need is the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device #TH62RE.

view full answer...

Answer 3

Yes, we do have the part you are looking for - the matching top and bottom spar hangers. The parts are as follows: - Replacement Bottom Spar Hanger for Thule T2 Classic Bike Platform Rack #753358402 - Replacement Top Spar Hanger for Thule T2 Classic…

view full answer...

Answer 4

The parts that you need for your Thule T2 Classic TH9044 are the following parts: - Replacement Top Spar Hanger for Thule T2 Classic Bike Platform Rack #853595202 - Replacement Bottom Spar Hanger for Thule T2 Classic Bike Platform Rack #753358402

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Replacement Parts Needed For The Thule DoubleTrack Pro XT Bike Rack

Product Page this Question was Asked From

Continue Researching