Hardware to Install Fusion LED Combination Tail Light Bar On Trailer Frame

Question

Question:

What type of screws do I need to attach these to a steel trailer frame?

asked by: Matt

0

Expert Reply:

Hi Matt; I would grab some self-tapping screws and drill a pilot hole to install the # STL264RB.

expert reply by: Robin H

0

Robin H.

12/15/2025

Hey Matt, how did the self-tapping screws work for mounting the tail light bar to your steel trailer frame? Your results could really help others figuring out the best way to secure theirs.

Reply

Answer 1

Both the turn signal and brake light wire on your RV can be spliced directly to the stop/turn signal light wire on the Fusion LED Combination Tail Light Bar #STL264RB but the bar isn't going to function perfectly. This is because when braking and…

view full answer...

Answer 2

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 3

Hi Jose, If you're saying you want to switch both tail lights to LED light strip-style tail lights then I have a few recommendations depending on the length you'd like: 12-5/8" long x 1" wide x 1/2" tall: Thinline LED Trailer…

view full answer...

Answer 4

The Fusion LED Combination Tail Light Bar for Trailers Over 80" Wide item #STL264RB are sold individually. It measures 20-1/2" long x 1" tall x 3/4" deep.

view full answer...

Answer 5

We have some light bars that will work with a platform style bike rack like your Hollywood Racks Sport Rider #HLY84FR, but there is no light bar made for your bike rack specifically. Can it be done? Yes, but you will need to find a safe way of…

view full answer...

Answer 6

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 7

Hello Mike, thanks for reaching out. Is the rear of your van sagging at all? The SuperSprings Custom Suspension Stabilizer and Sway Control Kit #SSA43 is more for reducing sagging which will in turn help with stability, handling and sway reduction.…

view full answer...

Answer 8

Hey Bobby, we have the Firestone Ride Rite kit part #F33VV that is a confirmed fit for your 2024 GMC Canyon AT4. Whenever available I recommend the Firestone kits as they have the highest quality bags. Are you wanting a compressor kit too?

view full answer...

Answer 9

I have another option for you, but the Timbren Heavy-Duty Axle-Less Trailer Suspension - Straight Spindle - Regular Tires - 3,500 lbs #TASR35HDS04 you were looking at actually uses 5200lb hub and drum assemblies and is not available with the 5 on…

view full answer...

Answer 10

Although the #TASR35HDS04 Timbren Axle-Less suspension you'd looked at has a 3500 lb capacity but is compatible with hubs that would have a 5200-7000 lb capacity, depending on which bearing set is used. We don't offer an idler hub compatible…

view full answer...

Answer 11

Hi Dave! I am not aware of an adapter that will do what you want, so I think the etrailer Electric Trailer Jack w/ 7-Way - Drop Leg - A-Frame - 22-1/2" Lift - 5K #e74GV is your best option. It is also the quickest and easiest way to proceed.…

view full answer...

Hardware to Install Fusion LED Combination Tail Light Bar On Trailer Frame

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching