How to Determine Correct Galvanized Trailer Hubs For Venture VAB-2825 Boat Trailer
Updated 12/15/2025 | Published 11/08/2024 >
Question:
Hi, I have a Venture VAB 2825 Boat trailer. I would like to upgrade my hubs to galvanized. How do i know what hub to buy? Thank You
asked by: Jeff D
Expert Reply:
Hi Jeff,
To find the correct hubs for your Venture VAB-2825 boat trailer, you'll need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them.
However, if you are unable to find them, you need to use a digital caliper and measure your spindle where the bearings ride, like in the diagram I added below. I did some checking and it looks like your VAB-2825 has a 3,525 lb GVWR, so I believe you have 3,500 lb axle, so it's possible you can use the galvanized Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-35-G-EZ-K.
This uses inner bearing L68149 (1.378" inner diameter) and outer bearing L44649 (1.063" inner diameter), so please be sure to verify, but if that matches what you have, it's exactly what you'll need. If not, I have added a link below to our entire selection of hubs for you.
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Idler Hub
- EZ Lube
- L68149 / L44649
- Marine Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: cotter pin
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Shop: CE Smith Spindle Nuts, Washers, and Cotter Pins for 1" Axle - Qty 2
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Optronics Mini Trailer Clearance or Side Marker Light - Submersible - Incandescent - Red Lens
- Shop: Dexter DX6.6 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 6,600 lbs
- Q&A: How to Determine Which Brake Pads Work on my Trailer?
- Shop: V-Shaped Identification Light Bar for Boat Trailers - Submersible - Red LEDs - Red Lens
- Shop: DeeMaxx Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Maxx Coating - 3,500 lbs
- Article: Trailer Wiring Diagrams
- Search Results: trailer tires and wheels
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Search Results: trailer jack
- Search Results: trailer wiring
- Shop: Brake Controller
- Search Results: trailer lights
- Shop: Gooseneck Hitch
- Search Results: trailer leaf springs
- Shop: Fifth Wheel Hitch
- Q&A: Correct Replacement for UFP H-1377 Trailer Hub
- Q&A: Correct Replacement for TDE 46210 Trailer Hub
- Q&A: Replacement Hub for a UFP H-1377 on a 2004 Tahoe Boat Trailer
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Q&A: Looking for Pre-Greased 3,500 Idler Hub that is Galvanized for Trailer Axle
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Replacement Hub for TDE Hub 46210 of Boat Trailer
- Article: How to Tell the Weight Rating of a Trailer Axle



Kate F.
12/15/2025
Hey Jeff, did the galvanized hub you picked out end up matching the bearings on your Venture trailer? Knowing how that fit worked out could really help others upgrading their hubs too.