Correct Replacement for UFP H-1377 Trailer Hub

Question

Question:

I need a direct replacement for a UFP H-1377b hub. Do you offer one that will match the specs?

asked by: Cliff B

0

Expert Reply:

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part # AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

expert reply by: Conner L

0

Answer 1

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 2

Hello Scott, thanks for reaching out. So you are correct the surge actuator would need to be disabled when switching over to EOH brakes. We do not sell a product for this, other than to replace the entire coupler with a standard one. You could have…

view full answer...

Answer 3

Yes, the CE Smith Trailer Hub part #CE13511 will fit as a replacement for your DICO hub 45264 but you will need to use a different seal as we have found that your spindle diameter is slightly different which means you need the #168255TB as well.

view full answer...

Answer 4

Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…

view full answer...

Answer 5

I'm sure we can get you a pre-greased hub assembly to replace your UFP H1377, but I was unable to find any definitive information on exactly what will replace this hub. So in order to find the correct hubs you will need to take apart your current…

view full answer...

Answer 6

The Progressive Dynamics PD9100L part #PD9160ALV is exactly what you are looking for. It's a lithium only battery charger that is rated for 60 amps so it would be perfect for you.

view full answer...

Answer 7

Your H-1377 hub is for a standard 3,500 lb axle so I recommend replacing it using the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles #AKIHUB-545-35-G-EZ-K which comes with the bearings, grease seal, lug nuts, and EZ Lube grease cap.

view full answer...

Answer 8

We don't have exact specs on the part that you're referring to, but I do know that's a stamp on a UFP hub, so I was able to reach out to my tech contact at Dexter UFP and he said that most of the hubs that number would be stamped on use a…

view full answer...

Answer 9

The difference between the two trailer tire sizes is that the letter D in the first size you listed ST205/75D15 stands for bias ply and the letter R in the tire size that they put on your vehicle stands for radial. Radial tires are preferred over…

view full answer...

Answer 10

We only have one replacement lens option which is the Replacement Amber Lens for Furrion Vision S Side Marker Light RV Cameras #C-FOS07TAPK-002 which fits on the Furrion Vision S #FCE48TASL, #FCE48TASL-05, and #FCE48TASL-07. If you find that your…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

For a 3,500 lb hub/drum replacement that will work well to replace your AL-KO 8500 you'd want the hub part #84546UC3-EZ which fits the spindle and has the 5 on 4-1/2 inch bolt pattern you need. For brake assemblies then the Electric Brake…

view full answer...

Correct Replacement for UFP H-1377 Trailer Hub

Product Page this Question was Asked From

Continue Researching