How To Install Thinline LED Trailer Tail Light As Center Brake Light
Updated 12/22/2025 | Published 10/24/2024
Products Featured in This Question
Question:
can you a give a step by step on how to install this light as a center brake light on my tailer? does it matter if i hook into my left or right tail lgiht? thank you!
asked by: Marcus
Expert Reply:
Hello again Marcus; I would be happy to help you sort out the installation of the # STL64RB. You're going to need some extra wire to run this to the center of your trailer so you can use the # 16-1-1 to match the 16 gauge wire that comes with the light. It doesn't matter which side you want to connect the light to so if one is easier to access that is what I would choose.
The white wire is the ground, the black is the tail light circuit, and then the red wire will tap into the stop/turn signal. More than likely you have the standard colors so brown will be the tail lights and green/yellow will be the stop/turn depending on the side. Sometimes wire color varies so it may be necessary to test the wires with a circuit tester # PTW2993 to find the function.
Since the stop/turn signals are combined you will want to filter out the turn signal using the # PP20-702. I went ahead and added the wiring diagram below. This will allow your light to turn on with the brakes but not with the left or right turn signal.
Product Page this Question was Asked From
Thinline LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 15 Diodes - Red Lens
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- Strip Light
- Surface Mount
- Submersible Lights
- LED Light
- 20L x 1W Inch
- Red
- Optronics
more information >
Continue Researching
- Search Results: mcl91ab
- Video: What to Know About the Thinline LED Clearance and Side Marker Light
- Video: Complete Breakdown of the 3rd Brake Light Logic Module
- Shop: 3rd Brake Light Logic Module
- Shop: Vehicle Tow Bar Wiring
- Shop: Curt 2-to-3 Tail Light Converter for Towed Vehicles w/ Incandescent Tail Lights
- Q&A: How to Wire a Third Brake Light on a Camper Shell
- Shop: Peterson LED Identification Light Bar for Trailers over 80" - 6 Diodes - Rectangular - Red Lens
- Shop: Identification Light Bar for Trailers over 80" Wide - Submersible - 3 Diodes - Red Lens
- Shop: Optronics LED Combination Trailer Tail Lights - Submersible - 40 Diodes - Driver and Passenger Side
- Shop: GloLight Thinline LED Trailer Light - Brake, Tail, Turn - Submersible - Red - 17" Long
- Shop: Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber
- Search Results: breakaway kit
- Q&A: Wiring Diagram for Dexter DX Series Electric Over Hydraulic Brake Actuator
- Search Results: 118158
- Article: Trailer Wiring Diagrams
- Q&A: How to Wire a Third Brake Light on Trailer
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Measuring To Choose The Right Trailer Axle
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
on Trailer Lights
Robin H.
12/22/2025
Hey Marcus, how did the wiring go for the Thinline LED light on your trailer? Did the logic module work as expected to keep the turn signals separate from the brake light? Sharing what you found could help others setting up a similar light.