Wiring Diagram for Dexter DX Series Electric Over Hydraulic Brake Actuator

Question

Question:

I have a Dexter electric-Hydraulic Brake Actuator for my boat trailer with all new brakes. How do I wire all of this together? Do you have a wiring diagram?

asked by: Allen B

0

Expert Reply:

We do have a wiring diagram for you! Whether you have the 1,000 psi Dexter DX Series # K71-650 or the 1,600 psi Dexter DX Series # K71-651 the wiring will be the exact same. I have attached a wiring diagram and review videos for you to check out. Just let me know if you have any additional questions regarding the installation.

expert reply by: Jon G

0

click to enlarge

Answer 1

Hey Don, welcome back! The Under-Bed Rail and Installation Kit #RP67KR for your 2024 F-350 matches the OEM prep package. You are not limited to Reese 5th wheel hitches. This can be used with the B&W Companion #BWRVK3300 and #BWRVK3305 or slider…

view full answer...

Answer 2

Wiring connections for the Electric Over Hydraulic Brake Actuator are as follows. Yellow - Cold side of breakaway switch, The wire that goes hot when a breakaway occurs. Black - Positive connection on breakaway switch, The wire that charges the…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

I have a couple close but not perfect to your measurements. The 2" Lubed Dust Cap & Rubber Plug - 1.99" part #DC200L-DCRP is an extremely common cap size found on a lot of trailers. Sometimes the hub will have a small bevel on them that…

view full answer...

Answer 5

The information we have that states that the Dexter Electric Over Hydraulic Actuator part #K71-651 will work with the 2015 GMC Sierra integrated brake controller came straight from Dexter so we know it will fit and work well.

view full answer...

Answer 6

Hey Bob, the Dexter electric over hydraulic brake actuator part #K71-651 can be used with the integrated brake controller of a 2012 GMC Sierra but you would need to use the adapter part #DX35FR.

view full answer...

Answer 7

Sounds like an internal issue with the circuit board which you'd have to speak directly to them about: [email protected]

view full answer...

Answer 8

I do have an option for you but we don't offer replacement circuit boards for any of our electric over hydraulic brake actuators and if I'm being honest here, that is no something you can purchase and replace yourself. If you wish to have…

view full answer...

Answer 9

When it comes to the wiring for the Dexter Electric Over Hydraulic Brake Actuator, #K71-651: 1. The black wire will connect to the 12V circuit coming from the vehicle's trailer wiring that is always hot. 2. White is the ground. 3. The yellow wire…

view full answer...

Answer 10

This is definitely something that is frustrating and unfortunately, my answer is not going to be much better. When we have brought this to Dexter in the past, they have told us that their Electric Over Hydraulic actuators like the Dexter DX Series…

view full answer...

Answer 11

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 12

You need the Wheel Retaining Ring #33-52-1 for your 10K axles and wheels. This ring has the single tab and will allow you to use your current flat faced wheel with Coned Lug Nuts #6-109. The retaining ring will sit outside the the wheels(see image).…

view full answer...

Wiring Diagram for Dexter DX Series Electric Over Hydraulic Brake Actuator

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching