Availability of Replacement Hitch Install Hardware for Curt Hitch 13465

Question

Question:

Hi, I need installation hardware for a curt 13465 hitch. Is a kit available? thank you Mike

asked by: Mike

0

Expert Reply:

Hey Mike, yes we have replacement hardware for all of the hitches we carry including the part # 13465 with the part # RHK. You'd just need to enter the part number for the hitch on the product page and we'll ship you out the correct hardware.

expert reply by: Jameson C

0

Jameson C.

12/22/2025

Hey Mike, did the replacement hardware kit work out for your Curt hitch? Knowing how it fit could help others looking for the same setup.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 5

OEM brake controllers integrate into the dash display of the vehicle which is why they require programming whereas aftermarket brake controllers like the Tekonsha #90885 do not at all so they don't require it. All you need to install this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

For the Draw-Tite Max-Frame Trailer Hitch item #76145 you are going to want the Curt Towing Starter Kit for 2" Hitches item #C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2"…

view full answer...

Answer 8

I have a solution for you but the Curt Trailer Hitch item #13465 will not give you enough clearance to mount the Kuat Sherpa 2.0 Bike Rack for 2 Bikes item #SH22B. The hitch pin hole sits too far underneath your car when installed. Instead you will…

view full answer...

Answer 9

I will be happy to explain how to install the shock kit #LC281281. In addition to the instructions below I have also included a picture of the actual instructions. 1. Raise trailer and jack up the axle to release pressure on the springs. 2. Remove…

view full answer...

Answer 10

Since the Curt Hitch #12240 that you referenced has a 1-1/4 inch hitch opening there is not a weight distribution system available for this vehicle since all the systems we offer are for hitches with 2 inch openings. There is an adapter available…

view full answer...

Answer 11

The best way to determine which ball mount is right for your 2005 Chrysler 300c and your trailer is to take a few simple measurements. Since you don't have the hitch we can see by the video of the Curt #13465, I've attached, that the hitch…

view full answer...

Availability of Replacement Hitch Install Hardware for Curt Hitch 13465

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching