Ball Mount Kit, Trailer Hitch, and Wiring Harness for a 2010 Dodge Challenger

Question

Question:

regarding ITEM # 76145 trailer hitch for Dodge Challenger Can you please recommend the proper mount and ball for this vehicle please?

asked by: Jackson G

0

Expert Reply:

For the Draw-Tite Max-Frame Trailer Hitch item # 76145 you are going to want the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It also includes a hitch pin and clip, hitch receiver lock with keys, hitch cover, and a storage case.

This hitch is confirmed to fit your 2010 Dodge Challenger unless you have the quad tip exhaust. If you have the quad tip exhaust you will want the Curt Item # 13465.

If you also need a wiring harness for your trailer lights you will need the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118404. This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk, behind the tail lights.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Answer 10

Hello Mike, thanks for reaching out. We do offer a few different hitches for the 2026 Subaru Crosstrek, the Curt #C22MJ, the Draw-Tite #76209 and the EcoHitch #EH57CR. All 3 of these hitches place the receiver in virtually the same position beneath…

view full answer...

Answer 11

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Ball Mount Kit, Trailer Hitch, and Wiring Harness for a 2010 Dodge Challenger

Products Featured in This Question

Continue Researching