Recommended Replacement Lens for a SAE IST-99 Clearance Lights

Question

Question:

I have a Kubota tractor with amber warning lights and I need four amber lenses. The number on the lens is SAE IST-99 D.O.T. and are about 4 in diameter. Can you provide me with four of them? Thank you

asked by: Richard K

0

Expert Reply:

Richard, it looks like you can use 4 of the Replacement Lens for Round Trailer Clearance and Side Marker Light # A52AB. These are the lenses for the Dual-Face Trailer Parking/Turn Signal Light # ST52AA which look to be very similar to the SAE IST-99 light you have.

expert reply by: Bryce D

0

Guillermo P.

2/24/2025

Im looking for the same thing but need a red lens

Bryce D.

2/24/2025

@GuillermoP Hey Guillermo, it sounds like you're looking for the Replacement Tail Light Lens for ST51RB and ST52RB # A52RB.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

Hey Ryan! You can use the Flex Power 2,200-Watt Portable Inverter Generator #FP34FR with your 30a hookup as long as you connect it with the correct extension cord and RV adapter, like #CAM55223 or #A10-1530DBK. The important thing to keep in mind is…

view full answer...

Answer 8

Hey Don, yes the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR that you referenced is rated for use at the rear of a flat towed vehicle. It might seem weird that some racks aren't rated for this but the reason for this is because flat towed…

view full answer...

Answer 9

Hello Dave, Thanks for writing in! I ran into the same thing you did. I couldn't find a dedicated hitch cover for a 3" receiver either. I'm going to reach out to our manufacturers to see why there aren't any available. In the…

view full answer...

Answer 10

Hey Randy, welcome back and congrats on the new truck. For a 450 lbs - 500 lbs tongue weight, I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ90-00-0600. This system will let you back up with it installed and…

view full answer...

Answer 11

We do not have custom channel nuts. Unfortunately, our best option for you would be to remove the tracks on your RSI Smart Cap and just install the corresponding length Rhino-Rack tracks. I have included a weblink to our Rhino-Rack track options…

view full answer...

Recommended Replacement Lens for a SAE IST-99 Clearance Lights

Product Page this Question was Asked From

Continue Researching