Does The Dutton-Lainson Pull Pin, Easy Swivel Trailer Jack Come Without The Weld Plate

Question

Question:

Hi, Im wondering if I could buy Item DL22686 without the weld plate. I found Item TJB-MB to replace it but would like to buy them separately if possible. Thank you.

asked by: Mitch R

0

Expert Reply:

Hi Mitch,

The Pull Pin, Easy Swivel Trailer Jack with Foot # DL22686 is only available with the weld plate included.

expert reply by: Kevin C

0

Answer 1

Hey Scott, thanks for reaching out. I like where you're headed, but unfortunately, we don't have a jack that checks every one of those boxes. The Dutton-Lainson #DL22686 is unique because of its black finish and weld-on design, but it…

view full answer...

Answer 2

Hi Kenneth, The Fulton Boat Trailer Jack w/ Wheel #FTJ120W0301 is a great cost effective option for your trailer. It's going to come with a weld-on mounting plate and snap ring to attach the jack. It has a 1,200lb capacity, comes with a wheel…

view full answer...

Answer 3

It looks like the jack on the trailer is a Reese swivel jack. The Fulton jack you referenced #FXP15W, should fit in its place no problem. Fulton and Reese are sister companies. However, the bolt holes are 3 inches on center. You will most likely have…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does The Dutton-Lainson Pull Pin, Easy Swivel Trailer Jack Come Without The Weld Plate

Product Page this Question was Asked From

Continue Researching