Parts Needed To Add A Brake Controller To A 2022 Jeep Wrangler Unlimited
Updated 03/25/2024 | Published 03/24/2024
Products Featured in This Question
Question:
I have a Jeep Wrangler with a 4 pin, I need a break controller for a camper. What else do I need, would I need something for a 7 pin?
asked by: Stephen V
Expert Reply:
Hi Stephen,
To add in a 7-way and brake controller to your 2022 Jeep Wrangler you'll need the following components:
First you'll need to install the 7-way # ETBC7. This will have a 4-pole connector to plug into your 4-pole connector for the light functions and then will need to be wired in the following manner:
Black - 12v power with included inline 40 amp circuit breaker.
White - ground to the frame.
Yellow - cap off with electrical tape unless you want to splice into the reverse light circuit for a boat trailer
Blue - brake output from brake controller.
You'll use the included 10awg wire to run from the 7-way up to the engine compartment and then split the casing to put the white wire through the firewall to connect to the brake output wire for the brake controller and the black wire will run to the battery with the inline circuit breaker.
From there you'll need a brake controller like the Redarc Tow-Pro Liberty Brake Controller # RED24FR along with the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers # RED69FR. This brake controller has a tiny controller that you can drill into the dash to avoid knocking your knee on it every time you get in or out of the Wrangler. The wires will need to be spliced in the following manner:
Black - 12v power with inline 30 amp circuit breaker from # ETBC7 installation kit.
White - ground to frame
Blue - brake output wire to 7-way
Red - cold side of the brake light switch
Since the brake light switch isn't useable you'll need to install the Roadmaster Stop Light Switch Kit # RM-751490 in order to get the brake signal.
Product Page this Question was Asked From
Roadmaster Universal Stop Light Switch Kit
- Flat Tow Brake System
- Stop Light Switch
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: tow bar
- Search Results: base plates
- Search Results: base plate
- Search Results: hitch pins and clips
- Search Results: locking hitch pin hitch pins and clips
- Search Results: blue ox base plate
- Search Results: rm 88400
- Shop: Vehicle Tow Bar Brake System
- Video: Review of Blue Ox Tow Bar - Avail Non Binding Tow Bar 2-1/2 Inch Hitch - BLU78QV
- Shop: Roadmaster Universal Stop Light Switch Kit
- Shop: Blue Ox Avail Non-Binding Tow Bar - RV Mount - 2-1/2" Hitch - 10,000 lbs
- Shop: Roadmaster Stop Light Switch Kit
- Shop: Curt RVi Series Breakaway System
- Shop: Base Plate for Tow Bar
- Shop: Blue Ox Alpha Non-Binding Tow Bar - RV Mount - 2" Hitch - 8,000 lbs
- Shop: etrailer Invisible Base Plate Kit - Removable Arms
- Shop: Roadmaster Direct-Connect Base Plate Kit - Removable Arms
- Q&A: Best Flat Tow Setup for 2026 Jeep Wrangler
- Shop: Trailer Wiring
- Video: Complete Breakdown of the Roadmaster Universal Stop Light Switch Kit
- Q&A: Recommended Flat Towing Parts for a 2023 Jeep Wrangler 4xe
- Video: Review of CURT RVi Series Breakaway System - RVI97FR
- Shop: Brake Controller
- Video: In-Depth Review of the Roadmaster Universal Stop Light Switch Kit
- Video: Set up: Blue Ox Alpha 2 Non-Binding Tow Bar on a 2020 Jeep Wrangler
- Video: Roadmaster Brake-Lite Relay Kit Comprehensive Review
- Q&A: Troubleshooting Blue Ox Alpha Arms Not Both Fully Engaging
- Shop: BOLT brand vehicle and hitch locks
- Video: Review of Roadmaster Tow Bar Wiring - Bypasses Vehicle Wiring - RM47ZR
- Q&A: Is Drilling Required To Install The etrailer Invisible Baseplate # e44FV On A 2023 Jeep Wrangler