Is the Curt Trunnion Style Weight Distribution System # 17302 Compatible with Surge Brakes

Question

Question:

Will this system work with surge controlled brakes - single axle boat trailer?

asked by: Rich H

0

Expert Reply:

Yes, the Curt Trunnion Style Weight Distribution System # 17302 that you referenced is compatible with surge brakes so it should work well on our single axle boat trailer with surge brakes.

I attached an FAQ on weight distribution systems for you to check out also.

expert reply by: Jameson C

0

Answer 1

For your application I recommend going with the Curt MV Weight Distribution (WD) #C17057 instead of the Curt #17302 because the part you mentioned is only rated for up to 1,000 lbs tongue weight while the MV I recommended is rated for 1,000 lbs -…

view full answer...

Answer 2

Since you are using a weight distribution system like the Curt MV Weight Distribution System #C17052 you will need a Reese Pole-Tongue Adapter #RP58393 that is designed for use with the chain style hangers. This has the structure to support the…

view full answer...

Answer 3

When picking out a weight distribution system the most important factor to consider is the loaded tongue weight which includes the the weight of any cargo behind the rear axle. Since your trailer has surge brakes you cannot use a weight distribution…

view full answer...

Answer 4

Hello Jason, thanks for reaching out. An Equal-i-zer Weight Distribution System is what I recommend for that since they are surge brake compatible. If you can tell me the GVWR or tongue weight of your camper I can recommend the correct WD hitch.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

This is a great choice Joe and thanks for reaching out! Weigh Safe True Tow Weight Distribution Hitch #WS49MR would be a good match for your setup. Since your Grand Design toy hauler will have a loaded tongue weight between 1,300 and 1,600 lbs, this…

view full answer...

Answer 9

Hi Mike; we don't have a way to swap out the 2" ball on the Andersen Weight Distribution Hitch #AN88VR. We do have the 2-5/16" ball separately, #AN45VR, but we don't have it as a complete system. If you really want the Andersen,…

view full answer...

Answer 10

Welcome back Belinda! The Andersen Weight Distribution Hitch w Sway Control - 4" Drop/Rise - 16K GTW, 1.6K TW #AN33VR may work for towing your Grand Design Imagine XLS23LDE with your F-250. However, when we tested it a while back, we didn't…

view full answer...

Answer 11

Hey Rex! Those are some great questions. A weight distribution hitch (WDH) isn't always needed but in your case you will want one. Typically if the weight of your trailer is more than 50% of the weight of your vehicle it is a good idea to use a…

view full answer...

Answer 12

Welcome back Don! The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET is exactly what I would recommend using. This is a solid reliable system and the built in sway control will make a noticeable improvement in ride…

view full answer...

Is the Curt Trunnion Style Weight Distribution System # 17302 Compatible with Surge Brakes

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching