Replacement Hinge for Extang Trifecta Tonneau Cover

Question

Question:

Broken hinge on my trifecta extang signature series tonneau. Part # on it is 35440500. Is this one of the two shown on your site? Thanks.

asked by: Gary C

0

Expert Reply:

Hey Gary, for your Extang Trifecta tonneau cover the correct replacement hinge would be the part # EX1032 that you referenced.

expert reply by: Jameson C

0

Answer 1

You would want the whole hinge assembly, #EX1033, especially if you have frequent breakage like you have described. There could be fatigue to the other components so to ensure maximum longevity I do recommend the whole hinge assembly. It is possible…

view full answer...

Answer 2

We do not offer any replacement parts that directly are for your Gator tonneau cover, however Extang also made Gator covers so their tailgate hinge #EX1033 and their cab side hinge #EX1032 may work for you, however you're going to want to make…

view full answer...

Answer 3

We do have that part for you! The correct part is the Replacement Tailgate Hinge for Extang Trifecta and eMax Tonneau Covers #EX1033. This is the same part as Extang's 35440400 that you reference.

view full answer...

Answer 4

We don't offer the Gator branded tonneau covers, and parts like these aren't typically tested for compatibility across brands. With that said, I've included a diagram that gives the measurements of the #EX1033 hinge so that maybe…

view full answer...

Answer 5

Hi Guy, For the tailgate side you'll want the Replacement Tailgate Hinge for Extang Trifecta and eMax Tonneau Covers #EX1033. If you end up needing to replace the cab side then you'll want part #EX1032 as well.

view full answer...

Answer 6

We have some replacement parts for Extang Trifecta Tonneau Covers. We have a cab side hinge #EX1032 and a Tailgate side hinge #EX1033. We also have some clamp accessories I've linked to assist. We also have the corner brace assembly #EX1041 and…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Hinge for Extang Trifecta Tonneau Cover

Product Page this Question was Asked From

Continue Researching