Why Do Two FastGun Turnbuckles TLS9522 Cost Less Than TLS9529-2-LK

Question

Question:

I am looking at Fast Gun turnbuckles for frame mounted tie downs Why can I buy 2 sets of 2 each TLS9522 for $880 but a set of 4 is $969 TLS9529-2-LK

asked by: Richard B

0

Expert Reply:

Hey Richard, the # TLS9522 is just a set of two of the Grey FastGun Turnbuckles - nothing else. The # TLS9529-2-LK comes with four Grey FastGun Turnbuckles plus the set of four Fast Gun Locks # TLS9500. When you factor in the price of the lock set, it looks like it is the exact same price if you were to buy them separately or all together as part # TLS9529-2-LK. Prices may fluctuate slightly from time to time but this should always be the case.

expert reply by: Jesse M

0

Answer 1

First you will need to replace your factory hitch on your 2024 Ford F-350 with the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TL27CR. Then you will be able to attach the Rear Tie-Downs #TLR3504 to their receiver. For the front we have the…

view full answer...

Answer 2

Both the CargoSmart Anti-Rattle D-Ring Tie-Down Ancho #3486509 and the CargoSmart Removable D-Ring Tie-Down Anchor #3486510 have the weight capacity to handle what you are looking to do. So it really just comes down to preference on having the…

view full answer...

Answer 3

For your 2021 Ford F-150 Crew Cab Short Bed the Torklift Camper Tie Downs you'd want are the part #TLF2018 and #TLF3007.

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

Hello Mike, Sounds like you are getting things set up the right way and not going over your payload, I respect that. It looks like the weights are the same whether you have a 6 3/4' or 8' bed. If you happen to have an aftermarket hitch,…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Duane, Air Springs are better for leveling loads and will typically give you a rougher unloaded ride quality so these might not be the best option for your setup depending on what your intended use is. Air springs are the best option when it comes…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

Hello Bart, thanks for reaching out. I can definitely point you in the right direction, but I will need a bit more information on your truck before I can recommend the correct tie downs. Can you please answer the following questions for me? 1. What…

view full answer...

Why Do Two FastGun Turnbuckles TLS9522 Cost Less Than TLS9529-2-LK

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching