Correct Replacement Head For A Curt TruTrack Weight Distribution System C17500

Question

Question:

I have a Curt #17500 distribution hitch w/sway control. Just want to make sure the #17507 is the correct replacement head. Also, it is possible to get just the two bearings for the sway control without buying the entire head?

asked by: Steve B

0

Expert Reply:

Hey Steve, you are correct that the Head Unit # C17507 is the correct replacement head for your Curt # C17500 weight distribution hitch. Unfortunately, the bearings are not available individually so if they are in need of replacement, getting a whole new head will be your best bet.

expert reply by: Jesse M

0

Answer 1

Hey Dan, it sounds like you are in need of replacement 1,000 lb spring bars for your Curt weight distribution system which we offer with the part #C17337. For frame mounted chain hangers then we have the part #C17003. Do both of these match what you…

view full answer...

Answer 2

I will be happy to answer your questions on the Curt TruTrack weight distribution system #C17500. They are referring to the brackets that mount on the trailer and hold the spring bars. Lift bracket is a term more associated with chain hanging systems…

view full answer...

Answer 3

I have some good news to offset some of that anger from recently being scammed. We do indeed have all of the replacement parts available for the Curt TruTrack Weight Distribution System #C17500 and I will list them out below. Replacement L-Pins and…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...