Availability of Matching Bearing to Go with Race 1729

Question

Question:

I’m having trouble finding the actual bearing for the 1729 Timken cup.not sure how to measure either since the actual bearing desinagrated.

asked by: Edgar A

0

Expert Reply:

The Timken Race 1729 part # TMK66FR is associated with the bearings 1751, 1755, 1774, 1775, 1778, 1779, and 1780. We have the 1779 bearing with the part number # TMK94FR.

expert reply by: Jameson C

0

Answer 1

If the center to center bolt spacing of your existing wheels is 9.44 inches, and 4-1/2 inch wide wheels with a + 5mm offset would work with your trailer, the #AM20208 wheels would work well for you. Rather than having the wheel mounting pad (surface…

view full answer...

Answer 2

The Gen-Y GH-302 you referenced has round spring bars that were actually made by Curt. The part you are looking for is the Replacement Spring Bar for Curt MV Weight Distribution System - 1,400 lbs TW, part #C17074.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Availability of Matching Bearing to Go with Race 1729

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching