Replacement Hub For UFP H-1377 on EZ Loader Boat Trailer

Question

Question:

I need a replacement hub for a 2004 EZ Loader. Numbers stamped on hub are UFP, H-1377, M27E

asked by: Colby F

0

Expert Reply:

Hey Colby, thanks for the question, and we can get you the right replacement for the UFP H-1377 hub on your EZ Loader boat trailer. The right replacement for you is the following:

- Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-35-G-EZ-K

This is a galvanized hub so it's perfect for a boat trailer and is the right fit for your spindle so you're all set.

expert reply by: Kyle S

0

Answer 1

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 2

In order to find the correct replacement hubs for your Shoreland'r boat trailer, you need to first know what bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the…

view full answer...

Answer 3

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 4

Bearing Buddies #BB1980A-SS have a 1.98 inch bore. This will be the closest match for your 1.988 hub bore. They keep water and dirt out of hubs and bearings, they allow boat trailer wheels to be completely submerged, and stop corrosion and pitting on…

view full answer...

Answer 5

The UFP H 1377 we have found correlates to a 3,500lb idler hub. It appears it uses the 5 on 4-1/2" bolt pattern. You can verify this information by measuring your bolt pattern and checking the bearings used on your hub. I have linked an article…

view full answer...

Answer 6

I'm sure we can get you a pre-greased hub assembly to replace your UFP H1377, but I was unable to find any definitive information on exactly what will replace this hub. So in order to find the correct hubs you will need to take apart your current…

view full answer...

Answer 7

According to Dexter, this is a 3,750 lb torsion axle with a 90.3" hub face measurement. More than likely your axle uses #L68149 and #L44649 bearings with a #168255TB grease seal. You will need to verify this information since Dexter did not have…

view full answer...

Answer 8

Based on the corrosion I see on the parts I recommend the Stainless Steel Kodiak Disc Brake Kit #K2R35S for your trailer. This will use a 10" rotor and all the components are going to be stainless steel for corrosion resistance on one axle. You…

view full answer...

Answer 9

Your H-1377 hub is for a standard 3,500 lb axle so I recommend replacing it using the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles #AKIHUB-545-35-G-EZ-K which comes with the bearings, grease seal, lug nuts, and EZ Lube grease cap.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Hub For UFP H-1377 on EZ Loader Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching