Plug and Play Wiring Harness To Install Redarc Tow Pro Brake Controller On 2024 Ram 1500

Question

Question:

How does the Redarc brake controller wire to my 2024 Ram 1500?

asked by: Andre

0

Expert Reply:

The Redarc Plug-and-Play Wiring Harness # 331-TPH-020 will allow you to easily connect the Redarc Tow-Pro Elite Brake Controller # RED44FR on your 2024 Ram 1500.

expert reply by: Bud M

0

Answer 1

Yes, the 2019 Ram 1500 is pre-wired for a trailer brake controller. The Redarc Tow-Pro Elite Trailer Brake Controller part #RED44FR with the Redarc Plug-and-Play Wiring Harness for Tow-Pro Trailer Brake Controllers part #331-TPH-020 is the best…

view full answer...

Answer 2

Yes, you can absolutely install an aftermarket brake controller like the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 on your 2019 Ram 1500. There won't be any dealer programming required either. For this, you will also need the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Plug and Play Wiring Harness To Install Redarc Tow Pro Brake Controller On 2024 Ram 1500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching