Which Harness For Redarc Liberty Brake Controller For 2025 Ram 1500

Question

Question:

I bought a redarc controller from you. I am trying to install it into my 2025 Ram 1500 bighorn. There is no harness or instructions to install it into my truck. Do you have the harness and instructions?

asked by: Steven H

0

Expert Reply:

Hi Steven,

Thanks for the purchase and we do have the right harness for your 2025 Ram 1500 and the Redarc Liberty Brake Controller # RED24FR. The correct plug-in harness is the following part:

- Redarc Plug-and-Play Wiring Harness # 331-TPH-020

You can also find the instructions linked below.

expert reply by: Kyle S

0

Steve H.

9/27/2024

That is the harness from the unit that plugs directly into the truck? 2025 is different as far a ls plug location. Where is the plug on the truck?

Reply

Kyle S.

9/27/2024

@SteveH I apologize but I can't tell you; the 2025 Ram 1500 looks to be quite a mess with regards to where the plug is. The manufacturers of the brake controller parts (which is where we get our fit info until/unless we do an install and find different) are saying under the dash to the right of the steering column but I'm also seeing different things in forums so I apologize but that just isn't info I definitively have at this moment.

Reply

Steve H.

9/27/2024

@KyleS But it is the correct harness?

Reply

Kyle S.

9/30/2024

@SteveH Yes sir, per Redarc, this is correct.

Reply

Answer 1

The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. I attached a picture that shows what it looks like. I also attached installation instructions for the Tekonsha…

view full answer...

Answer 2

The bolts included with the Curt Trailer Hitch Receiver #C13240 referenced in your question are M10-1.25 x 30 inch hex bolts. If you are just needing the replacement hardware for the trailer hitch, you will use part #RHK. Once on the product page,…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hi Steven, Thanks for the purchase and we do have the right harness for your 2025 Ram 1500 and the Redarc Liberty Brake Controller #RED24FR. The correct plug-in harness is the following part: - Redarc Plug-and-Play Wiring Harness #331-TPH-020 You can…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Which Harness For Redarc Liberty Brake Controller For 2025 Ram 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching