7-Way Install Kit for a 2016 Mercedes-Benz Sprinter 2500

Question

Question:

Looking for a wiring harness for my 2016 Mercedes sprinter 2500. My trailer has a 7 pin connector, round, with female blade terminals, so I’d want the sprinter to have male blades to connect to it

asked by: Michael B

0

Expert Reply:

For your 2016 Mercedes-Benz Sprinter 2500 you can use the Universal Installation Kit for Trailer Brake Controller # ETBC7 for a 7 way kit.

This kit will utilize an existing 4 pole connector, so if you don't have one you can add one with # C47NR.

expert reply by: Bryce D

0

Answer 1

Hey Nick, congrats on the new Sprinter. The Tekonsha Custom Harness item #3063-P does fit the green connector that is under your seat in your 2025 Mercedes Benz Sprinter 2500. It's compatible with the E98 prep package option as shown in the…

view full answer...

Answer 2

Hello Adam, thanks for reaching out. I am sorry to say we do not offer any wireless trailer lights that plug into the ODB port. I did look up these Sail Timers Speedy Trailer Lights online and it seems like an interesting invention, but I question…

view full answer...

Answer 3

What you have found is a USCAR style connector that was designed for the standard trailer 7-way so all you need to add a 7-way and 4-way is the part #30955 which plugs right into this.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

7-Way Install Kit for a 2016 Mercedes-Benz Sprinter 2500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching