Replacement 12" x 2" Electric Brake Assemblies With A 9-Bolt Mounting Pattern

Question

Question:

Im looking for brake assembly for Dexter axle 12x2 with a 9 bolt mounting flange plate.

asked by: Michael S

0

Expert Reply:

Since you said you have nine mounting holes you most likely have the Dexter Electric Brake Kit - 6K # 23-105-106-09. This has nine holes but you would only use four or five of them to mount the assemblies to the brake flange. The extra holes are just available to make mounting easier with certain brake flanges. These are rated for 6k so you'll want to check your axle for an axle tag and see what the axle capacity is. If you find it's 7k instead you'll want part # 23-180-181 instead.

expert reply by: Kevin C

0

Answer 1

The same answer would apply. The brake assembly #23-106-09 is designed to fit a Hayes/AL-KO or Dexter axle with either the 4-bolt or 5-bolt mounting flange. These are 12 x 2 inch brakes. To measure the drum you will measure the inside diameter. It…

view full answer...

Answer 2

The center hole of the brake assemblies #23-105-09 and #23-106-09 measures 3-3/16 inches across. The kit for both of these is the part #23-105-106-09 that you referenced.

view full answer...

Answer 3

Based on the mounting bolt hole spread you have an older ALKO/Hayes axle. For this we have the Left #23-105-09 and Right #23-106-09 brake assemblies. These brake assemblies have both the Dexter 5 bolt and ALKO/Hayes 4 bolt mounting patterns for the…

view full answer...

Answer 4

You'll need to do some quick measuring of your backing plate/brake flange to see if you can use the 6,000 lb Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand #23-105-09. I have added photos below that I hope will…

view full answer...

Answer 5

We have the brake assemblies you are looking for. The only 6k rated 12 by 2 inch assemblies we offer that have the same unique 4 bolt mounting patter are the #23-106-09 for the right hand side and part #23-105-09 for the left hand side.

view full answer...

Answer 6

view full answer...

Answer 7

It looks like the studs in your brake assembly are closer together (center to center) at the bottom. If the center to center bolt spacing matches the photo I've provided, then the #23-105-09 you'd looked at would be the correct replacement…

view full answer...

Answer 8

Most of our 12 x 2 electric drum brake assemblies like Dexter left/right kit #23-112-113 use a 5-bolt mounting pattern but the Dexter brake kit #23-105-106-09 has both 4-bolt and 5-bolt mounting holes. I went to our warehouse and measured the spacing…

view full answer...

Answer 9

Trailer brake assembly #23-105-09 is specifically designed to fit AL-KO/Hayes axles which are not as common as other axles. Brake assembly #23-105 fits Dexter axles and other more common axles. If you have an AL-KO/Hayes axle, then I would go with…

view full answer...

Answer 10

Dexter has discontinued the K71-048-00 brake linings (pad) for the 8-201 hub, but the #AKBRKR-S-12 would be a suitable substitute. The manual adjust brake assembly uses the same shoes for the right and the left brake assembly. We don't offer…

view full answer...

Answer 11

Nowadays you would be able to find the axle capacity stamped on your axles, but that was not always the case. If you are unable to find that information on your axles, you still have other options. The first thing I would do is try to determine the…

view full answer...

Answer 12

In order to install the Dexter Electric Trailer Brake Assembly part #K23-086-00 on your trailer you will need to install a brake mounting flange as well. Based on the photo you submitted, there isn't room to install a brake mounting flange on the…

view full answer...

Replacement 12" x 2" Electric Brake Assemblies With A 9-Bolt Mounting Pattern

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching