Comparing Trailer Brake Assembly # 23-105 and # 23-105-09

Question

Question:

Why the huge price difference between 23-105-09 and 23-105?

asked by: Robert

0

Expert Reply:

Trailer brake assembly # 23-105-09 is specifically designed to fit AL-KO/Hayes axles which are not as common as other axles. Brake assembly # 23-105 fits Dexter axles and other more common axles. If you have an AL-KO/Hayes axle, then I would go with them.

expert reply by: Michael H

0

Answer 1

The same answer would apply. The brake assembly #23-106-09 is designed to fit a Hayes/AL-KO or Dexter axle with either the 4-bolt or 5-bolt mounting flange. These are 12 x 2 inch brakes. To measure the drum you will measure the inside diameter. It…

view full answer...

Answer 2

Based on the mounting bolt hole spread you have an older ALKO/Hayes axle. For this we have the Left #23-105-09 and Right #23-106-09 brake assemblies. These brake assemblies have both the Dexter 5 bolt and ALKO/Hayes 4 bolt mounting patterns for the…

view full answer...

Answer 3

The center hole of the brake assemblies #23-105-09 and #23-106-09 measures 3-3/16 inches across. The kit for both of these is the part #23-105-106-09 that you referenced.

view full answer...

Answer 4

You'll need to do some quick measuring of your backing plate/brake flange to see if you can use the 6,000 lb Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand #23-105-09. I have added photos below that I hope will…

view full answer...

Answer 5

It looks like the studs in your brake assembly are closer together (center to center) at the bottom. If the center to center bolt spacing matches the photo I've provided, then the #23-105-09 you'd looked at would be the correct replacement…

view full answer...

Answer 6

view full answer...

Answer 7

Since you said you have nine mounting holes you most likely have the Dexter Electric Brake Kit - 6K #23-105-106-09. This has nine holes but you would only use four or five of them to mount the assemblies to the brake flange. The extra holes are just…

view full answer...

Answer 8

Most of our 12 x 2 electric drum brake assemblies like Dexter left/right kit #23-112-113 use a 5-bolt mounting pattern but the Dexter brake kit #23-105-106-09 has both 4-bolt and 5-bolt mounting holes. I went to our warehouse and measured the spacing…

view full answer...

Answer 9

We have the brake assemblies you are looking for. The only 6k rated 12 by 2 inch assemblies we offer that have the same unique 4 bolt mounting patter are the #23-106-09 for the right hand side and part #23-105-09 for the left hand side.

view full answer...

Answer 10

Nowadays you would be able to find the axle capacity stamped on your axles, but that was not always the case. If you are unable to find that information on your axles, you still have other options. The first thing I would do is try to determine the…

view full answer...

Answer 11

Dexter has discontinued the K71-048-00 brake linings (pad) for the 8-201 hub, but the #AKBRKR-S-12 would be a suitable substitute. The manual adjust brake assembly uses the same shoes for the right and the left brake assembly. We don't offer…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Comparing Trailer Brake Assembly # 23-105 and # 23-105-09

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching