Replacement Bearing Kit ad EZ Lube Grease Cap for Lippert 136214 Hub/Drum

Question

Question:

Hello, I have a lippert 136214 10 inch drum 6 bolt. I need a new bearing kit with seals. I also need the easy grease cap, and wheel center cap. Thanks

asked by: Jason

0

Expert Reply:

According to my research your Lippert 136214 hub uses the same parts as a 3,500 lb hub so you need the following:

- Hub Bearing Kit - 3,500 lb with #84 Spindle # BK2-100
- 2" Lubed Dust Cap & Rubber Plug # DC200L-DCRP

You'll need 1 of each kit per hub.

expert reply by: Jon G

0

Answer 1

For your application you need the Pre-Greased Easy Grease Trailer Hub and Drum Assembly #AKHD-655-35-EZ-K. This matches all of the specs you mentioned and while it's only rated for 3.5K axles, it will still work for your Lippert 4.4K axle since…

view full answer...

Answer 2

Hi John; what you have there is a Lippert 4,400 lb axle that is 85" long with a 68-1/2" spring center measurement. 4,400 lb axles are obsolete so you're looking at upgrading to a 5,200 lb axle. The closest thing we have is the Trailer…

view full answer...

Answer 3

Charles, for your camper with 4,400 lb axles you can use the Trailer Hub and Drum Assembly #8-407-5UC3-EZ. This hub and drum assembly will work with 4,400 lb axles, has a 6 on 5 1/2" bolt pattern, and includes the bearings, races, grease seal,…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Bearing Kit ad EZ Lube Grease Cap for Lippert 136214 Hub/Drum

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching