What Is The Correct Lug Nut For A PJ Trailer With ST205/75-15 Tires?

Question

Question:

What is the correct lug nut to use on a PJ Trailer with ST205/75/15 tires on it?

asked by: Art

1

Helpful Expert Reply:

The 15" wheels will use a 1/2" 20 lug nut. This is standard for virtually any 15" 5 lug or 6 lug wheel/ hub combination. Now I am not sure exactly when your trailer was made, but anything made within the last few decades should stick to this standard. I recommend using a one-piece chrome lug nut like part # AM90049 or # 12CLN.

expert reply by: Jesse M

1

Answer 1

The 5 means that the wheel is 5 inches wide from bead to bead (not overall width). The J indicates the design of the wheel bead seat but it is nothing you need to be concerned with as this is the most common shape for all trailer tires. To measure…

view full answer...

Answer 2

Thank you for your purchase of the Demco Channel Tongue Trailer Coupler - eZ-Latch. The diameter is 5/16" and the lock that is designed specifically for Demco couplers with the eZ-Latch is the following: - InfiniteRule Lock for Demco eZ-Latch…

view full answer...

Answer 3

In some cases trailer lighting will ground through the hitch ball but that's typically only if the actual ground circuit is insufficient. This is not an ideal setup. It needs to ground through the wiring of the trailer harness. You can test this…

view full answer...

Answer 4

You'd need to put a battery in your trailer so that you can power the trailer lights when you aren't connected to your tow vehicle. It would be a matter of just running a power wire from the battery to the lights. You'd need to charge the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Is The Correct Lug Nut For A PJ Trailer With ST205/75-15 Tires?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching