Recommended Spindle Nut Kit for an Axis 3.5K Axle

Question

Question:

hi i have a 3500# axle made by axis products serial no 87155 B 008 i need to know if this is the correct kit. thanks

asked by: Dave S

0

Expert Reply:

I wasn't able to find any info on that axle, however as long as you have a # 84 spindle, the Spindle Nut Kit for EZ Lube Axles # RG05-100 will work with your Axis 3.5K axle.

expert reply by: Bryce D

0

Answer 1

Sounds like you have the trailer hub part #8-247-50UC3-EZ installed on your trailer. That means for a grease seal you would need the part #RG06-050.

view full answer...

Answer 2

Hello Mel, great question! Yes, the Torklift tie downs part #TL66FV will fit your 2006 GMC Sierra 2500HD crew cab with the 8 foot bed, provided your truck does not have running boards or cab length boards that extend under the bed, and you are not…

view full answer...

Answer 3

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Hey Steve, happy to help! The Victron MultiPlus II #VN43VR you're looking at can replace many of the functions of your Magnum MS2812, but there's an important difference with the AC connections. The #VN43VR has one AC input and two AC…

view full answer...

Answer 6

Hey William, thank you so much for all of the information! To replace your axles, I recommend the Trailer Axle w/ Electric Brakes item #e73SR. This is a 6,000 lbs axle that come ready to install with pre-greased hubs and electric brake assemblies.…

view full answer...

Answer 7

Hi Randy; that part number corresponds with the OEM Chill Cube. At this time, there are no heat strips available from Furrion. They have said they are developing one, but it has been over a year with no word on an ETA. The only option for heat on a…

view full answer...

Answer 8

Hey Frank, thanks for reaching out! What Dexter Axle means by this is that you want the grease zerk fitting from the wet bolts in the Dexter E-Z Flex Suspension Kit #K71-653-00 to face the outside of the trailer, rather than under the trailer. I see…

view full answer...

Answer 9

Thank you for providing that information. Leaf springs like the ones you have now typically match the axle capacity on your trailer. Although adding leaf springs with a slightly higher capacity won't hurt, it also is not necessary. Based on the…

view full answer...

Answer 10

It sounds like you are looking for a u bolt kit for a 3,500 lbs axle. The 3-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 25-1/4" Long item #e57SR will work great for a tandem axle suspension system. For your ubolt kit you're going to…

view full answer...

Answer 11

Hi Austin, I can help you determine the right replacement double-eye leaf springs for your 2018 Jayco trailer, though we don't have any way of knowing what specific ones you need. It's pretty easy though, as all you need to do is measure your…

view full answer...

Answer 12

Timbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when…

view full answer...

Recommended Spindle Nut Kit for an Axis 3.5K Axle

Product Page this Question was Asked From

Continue Researching