Size of the Bolts that Come with the Timbren Suspension Enhancement System TGMFK25S

Question

Question:

What size are the bolts for part # TGMFK25S length and tread pitch? Thanks

asked by: Brett

1

Helpful Expert Reply:

I checked with Timbren and the bolts that come with the Timbren part # TGMFK25S that you referenced are M10x1.5X30.

expert reply by: Jameson C

1

Answer 1

Hi Chris; it looks like you already picked up the Timbren SES #TDR1500DQ along with the Spacer Kit #T68MR. The Timbren itself is 5-1/2" tall so 3" worth of spacers would do the trick if you follow the recommended 1" gap or 3-1/2"…

view full answer...

Answer 2

You would want to go with the Timbren kit that fits your 2020 Ram 1500 part #TDR1500DS and then since you have a 6 inch lift you'd need a quantity of 12 of the Timbren 1 inch spacers #A25723-90AH00 to take up the extra space.

view full answer...

Answer 3

If you had the tools to do the job right, there's no reason you couldn't cut the #RP45018 down to 34 inches to make it basically the shorter version part #RP45292. The shorter section of the extender where the 2 inch hitch opening is the same…

view full answer...

Answer 4

Hey good question, Adam. There is not a specific limit on how many spacers you can use with Timbrens. Most trucks that use Timbrens would not be lifted more than 4"-6" anyway, and I have heard of people using up to 6 spacers on each side. I…

view full answer...

Answer 5

I spoke with my contact at Timbren regarding the Rear Suspension Enhancement System #TDR2500D referenced in your question. The bolt that attaches the spring to the bracket should be be tightened to 33 foot pounds of torque. When the bolt is tightened…

view full answer...

Answer 6

Hello Rustic Hart Ranch, The Timbren Severe Service kit #TDRTT3500E is a great choice for your 2021 Ram 2500 carrying that 1997 Lance Legend 500 camper. It’s specifically designed to handle heavy, constant loads like yours and really helps reduce…

view full answer...

Answer 7

Hey Jacob, the ApexAnchor tie downs part number #TL38SV and #TL26SV work perfectly fine with running boards so you would not need to remove them.

view full answer...

Answer 8

For any running board/step, including the Bestop AMP Research, they will not interfere with the TorkLift camper tie-downs so long as the board/step does NOT go underneath the bed. So as long as the board ends before reaching the bed on your Ram…

view full answer...

Answer 9

I attached a picture that shows the Torklift Camper Tie Down #TLF2021 installed on a truck with a set of running boards. If the running boards are cab length they'd be fine, but if they go from the wheel well to wheel well they would interfere as…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Size of the Bolts that Come with the Timbren Suspension Enhancement System TGMFK25S

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching