Solution for Needing Longer Version of Hopkins Endurance Easy Pull 4-Way

Question

Question:

I was wondering if f you sold this product from Hopkins or if you could get it? 38133 Endurance™ Easy-Pull™ Jacketed 4 Flat Trailer Side 72 I would like to have this length as it works better for my trailer. Thank you

asked by: Travis M

0

Expert Reply:

We don't have the 72 inch version but for a longer option we do have the part # HM38136 which is 25 foot long and could be cut down shorter if needed.

expert reply by: Jameson C

0

Answer 1

Hi Robert! We have a couple options for a 25' long 4 flat. Our site can be weird sometimes, but not sure why it isn't showing you more options. Anyway, the Mighty Cord 4-Way Flat Trailer Connector - Wishbone Style - Trailer End - 25' Long…

view full answer...

Answer 2

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 3

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Solution for Needing Longer Version of Hopkins Endurance Easy Pull 4-Way

Continue Researching