What is the Best Hitch for a 2024 Hyundai Tucson?

Question

Question:

What's the best hitch for a 2024 Hyundai Tucson?

asked by: Bev

0

Expert Reply:

The best hitch for a 2024 Hyundai Tucson is the etrailer Hitch item # e38KR. This hitch is custom fit and bolts to your Tucson with included hardware. It is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 525 lbs maximum tongue weight. This is the highest capacity hitch available for your Hyundai.

The reason this is the best hitch is because the entire crosstube mounts behind the rear bumper cover. This leaves only the 2" receiver visible which not only helps with ground clearance but it also looks better.

If you are planning on towing you will also need a wiring harness item # C59236 and a ball mount kit item # C45534.

I recommend using the No-Drill Mount Bracket item # 18136 and the item # C42CR to secure the 4-way connector to your hitch. This will put it in an easy to reach spot and prevent the risk of it falling onto the road.

expert reply by: Jerred H

0

Answer 1

Hey Alan, the Curt hitch part #C94WR that you referenced is a confirmed fit for your 2025 Hyundai Tucson and the recommended install method is to remove the lower bumper panel and leave it off. There might be a way you could remove the panel and…

view full answer...

Answer 2

The trailer hitch I recommend for a 2023 Hyundai Tucson is the Curt Trailer Hitch Receiver part #C94WR which I confirmed as a fit with Curt for all models, including the Hybrid. This trailer hitch features a bolt-on installation so there is no…

view full answer...

Answer 3

I talked with the vendor about unmarrying the Edge CTS3 Tuner. You will need to go into the tune menu and look for 'return to stock' or 'backup'. This will walk you through the necessary steps to return your truck back to factory tune…

view full answer...

Answer 4

Hey Kyle, In order to unmarry your CTS2 from the vehicle you'll have to go into the tune menu and look for 'return to stock' or 'backup'. This will walk you through the necessary steps to return your truck back to factory tune and…

view full answer...

Answer 5

Hi Richard, Using a hitch adapter will reduce your trailer hitch's capacity by 50% and the use of an adapter isn't always allowed depending on the bike rack. You'll want to first check with the bike rack manufacturer if they allow for an…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi David; the Draw-Tite Max-Frame Trailer Hitch Receiver #75836 does not come with a bracket to mount the plug from trailer wiring. If you want to be able to mount a 4-way plug from your wiring #118812 you will need to pick up the #18144 separately.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...