Dimensions Of The RV Propane Gas Detector # RS64FR

Question

Question:

what size is it?

asked by: Mike

0

Expert Reply:

The RV Propane Gas Detector # RS64FR itself is 4-1/4" long x 2-5/8" wide x 1/2" thick. It also includes two trim plates to cover up the old cutout hole from previous detectors:

Larger trim plate: 7-1/4" long x 3-3/8" wide
Smaller trim plate: 5-3/4" long x 4-1/4" wide

expert reply by: Kevin C

0

Answer 1

The 2-Wire RV Propane Gas and Carbon Monoxide Detector #RS44FR can be mounted vertically if needed but most importantly should be installed no more than 18" from the floor so that it can accurately detect the amount of gas in your RV. Do not…

view full answer...

Answer 2

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The RV Propane Gas Detector part #RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

I wasn't able to find the Atwood 36720 RV Propane Gas Detector you mention, however I was still able to find the RV Propane Gas Detector #RS64FR in white, or #RS44FR in black to work as a replacement for your Protechtor Series 2001 LP Gas…

view full answer...

Dimensions Of The RV Propane Gas Detector # RS64FR

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching