Can The Lock N Roll Vehicle Side Hitch # 336VS503 Fit a Curt Adjustable Ball Mount # C45900?

Question

Question:

Is the Lock N Roll vehicle side 336vs503 compatible with the Curt channel that is included with the C45900?

asked by: Chuck

0

Expert Reply:

Yes, you can install the Lock N Roll Articulating Hitch # 336VS503 on the Curt Channel Style Adjustable Ballmount # C45900. The holes on the Lock N Roll are 5/8" diameter and spaced every 2" on center. This will fit the Curt having the same 5/8" diameter holes spaced every 1" on center. This will give you more adjustments than the Lock N Roll 3-Position # 336TS505 or 5-Position # 336TS515 receivers.

expert reply by: Bud M

0

Answer 1

Yes, the channel of the Curt Channel Style Adjustable Ballmount #C45901 that you referenced is compatible with the Replacement 2" and 2-5/16" Dual-Sided Hitch Ball #C45912.

view full answer...

Answer 2

I spoke with my contact at Lock N Roll about the Lock N Roll Articulating Hitch part #336VS503505 and they were not quite sure what measurements you are looking for nor was I. That said, I went out to our warehouse for you and jotted down a few…

view full answer...

Answer 3

The only difference between buying the Channel Bracket #336TS505 and the Channel Mount #336VS503 separately is only the fact that they are purchased separately. It's the same thing so grab whichever one saves you the most money. ON the trailer…

view full answer...

Answer 4

As long as your Grand Design Reflection 31MB has a 2" trailer hitch receiver on the back of it, and from the center of the hitch pin hole to the ground measures 19" - 39-3/4" then the MORryde Hitch Mounted Trailer Stabilizer for…

view full answer...

Answer 5

There isn't an exact schedule for how often to grease the Lock N Roll Articulating Hitch #336VS503 through it's low profile grease fitting but maybe twice a year under normal use. It really just depends on how often you are towing and the…

view full answer...

Answer 6

The channel of the #336TS505 is wide enough to accommodate the #BD028585 and #C25328 and the hole spacing is correct at 2 inches and hole diameters are 5/8 so it would work well.

view full answer...

Answer 7

To utilize the Lock N Roll coupler system on your trailer you'll need one of the following styles: - A-Frame #336TS504 - Flat Plate #336TS514 - 2" Channel #336TS528 - 2-1/2" Channel #336TS506 - 3" Channel #336TS508 The part…

view full answer...

Answer 8

Based on the images you sent in it appears your 2005 Starcraft RT10 does not use a traditional A-Frame coupler so the Lock N Roll #336TS504 will not work for your application. Instead you will need to measure the width between your frame rails the…

view full answer...

Answer 9

The #336VS503515 comes with the adjustable channel bracket along with the adjustable channel mount and bolts. You will need to install the channel mount in the appropriate rise/drop position since it does not come fully assembled. It looks like you…

view full answer...

Answer 10

For an articulating coupler and hitch for your tear camper I recommend using the Lock 'N' Roll System. The Lock 'N' Roll has 3 axis of direction allowing it to move up and down, side to side, and rotate 360 degrees. It also has a more…

view full answer...

Answer 11

Hello Mark; yes, the Replacement 2" and 2-5/16" Dual-Sided Hitch Ball #C45912 will fit the Curt #C45917 shank. The shank has a 3" wide channel with holes spaced 1" apart and the #C45912 ball is made for a 3" channel with…

view full answer...

Answer 12

Just the replacement ball mount platform of the part #C45901 is not available but I have a similar solution that might work for you. The part #C45912 fits the same Curt channel you have now and would give you a dual ball setup with a 2 inch and…

view full answer...

Can The Lock N Roll Vehicle Side Hitch # 336VS503 Fit a Curt Adjustable Ball Mount # C45900?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching