Will Dual-Sided Hitch Ball # C45912 Fit Channel of Curt Channel Style Adjustable Ballmount C45901

Question

Question:

Will this fit the channel of the curt c45901 hitch? Thank you

asked by: Ken

1

Helpful Expert Reply:

Yes, the channel of the Curt Channel Style Adjustable Ballmount # C45901 that you referenced is compatible with the Replacement 2" and 2-5/16" Dual-Sided Hitch Ball # C45912.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Yes, you can install the Lock N Roll Articulating Hitch #336VS503 on the Curt Channel Style Adjustable Ballmount #C45900. The holes on the Lock N Roll are 5/8" diameter and spaced every 2" on center. This will fit the Curt having the same…

view full answer...

Answer 2

As long as your Grand Design Reflection 31MB has a 2" trailer hitch receiver on the back of it, and from the center of the hitch pin hole to the ground measures 19" - 39-3/4" then the MORryde Hitch Mounted Trailer Stabilizer for…

view full answer...

Answer 3

I reached out to my contact at Curt and while I have a complete replacement option for you, the ball mount section of the #C45901 is not available separately. Since there is no other ball mount option of the same style that will fit your shank, you…

view full answer...

Answer 4

Hello Mark; yes, the Replacement 2" and 2-5/16" Dual-Sided Hitch Ball #C45912 will fit the Curt #C45917 shank. The shank has a 3" wide channel with holes spaced 1" apart and the #C45912 ball is made for a 3" channel with…

view full answer...

Answer 5

Just the replacement ball mount platform of the part #C45901 is not available but I have a similar solution that might work for you. The part #C45912 fits the same Curt channel you have now and would give you a dual ball setup with a 2 inch and…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Matt, welcome back! You are correct. The threaded hole on the Weigh Safe 180 Hitch 2-Ball Mount for 3" Hitch item #WS34MR ball retainer, is to make removing the pin easier. You can insert a 1/4"-20 screw to get additional leverage to…

view full answer...

Answer 12

Hey Adam, the correct Kuat DEK Platform rack with light bar for your 2026 Toyota Tacoma would be the part #KU73SR. The correct Kuat Ibex Overland Truck Cap then too would be the part #KU99SR that you referenced. Now the top of this would be lower…

view full answer...

Will Dual-Sided Hitch Ball # C45912 Fit Channel of Curt Channel Style Adjustable Ballmount C45901

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching