Availability of Air Lift Air Bag Kit that Fits 2012 Toyota Tacoma

Question

Question:

For my 2012 4WD Toyota Tacoma, is there a reason why I cant use the 5000 Ultimate with the internal jounce bumper? Id like to have that just in case I lose air pressure completely.

asked by: Douglas B

0

Expert Reply:

Air Lift has air bag suspension enhancement kits that fit your 2012 Toyota Tacoma 4WD like the part # AL49DQ but they do not offer a version that has the internal jounce spring. Some report that the jounce spring versions make the ride quality harsher so it would not be my favorite option to recommend.

expert reply by: Jameson C

0

Answer 1

Hello Brad, Great question! If you're planning to take your 2023 Toyota Tacoma off-road and you're using the Air Lift LoadLifter 5000 kit #AL49DQ, then adding the Air Lift Air Helper Spring Cradle #AL59DQ is a really smart move. These cradles…

view full answer...

Answer 2

Hey Alex, those are both really good questions. Let's start with the off-roading at full drop for the Air Lift bags on your 2021 Toyota Tacoma, which are the Air Lift LoadLifter 5000 Air Helper Springs #AL49DQ. When you are off-roading the…

view full answer...

Answer 3

Without knowing exactly what was done off-road it is difficult to say what would have damaged your #AL59561. Realistically this shouldn't be a problem as long as they are properly inflated and not overloaded. However, if you were driving through…

view full answer...

Answer 4

The Air Lift Ride Control helper spring #AL59564 has a max extension of 10.25", minimum compression of 3.1" and a 6.5-8.5" design height. Your should always stay at factory height and keep that 6.4-8.5" distance and this is…

view full answer...

Answer 5

Good question, and the difference between the Ride-Rite air bags for your 2021 Toyota Tacoma is actually the fit, as the right one will depend on if your leaf springs are above your axle or below your axle: - Axle Located Below Leaf Spring Pack:…

view full answer...

Answer 6

The reason the air bag kits like the part #AL59564 have a minimum pressure rating of 5 psi is that you need them to retain their shape at all times when the suspension is in use so that the bags do not fold which causes them to wear out prematurely.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Availability of Air Lift Air Bag Kit that Fits 2012 Toyota Tacoma

Product Page this Question was Asked From

Continue Researching