Bearing Kit for 2004 Ranger Boat Trailer

Question

Question:

I have a 2004 Ranger Boats trailer tandem axle. I need to replace seal, o rings and bearings with race. Called Ranger parts and they referred me to trailer. If I could have parts #s I would like to order from you. Thanks!

asked by: Steve W

1

Helpful Expert Reply:

The Bearing Kit # BK2-100 will contain the new bearings, races, grease seal, tang washer and cotter pin for replacing the bearings on your 2004 Ranger Boat Trailer.

If you happened to have an oil bath hub the seal you would need is the # XLPROLUBE1980SEAL.

expert reply by: Jameson C

1

Answer 1

The 11033L hub shown in your photo was manufactured by Tie Down Engineering, or TDE. What you have there is a hub for a standard 3500 lb axle which has a 5 on 4-1/2 inch bolt pattern. For an idler hub, I'd recommend the galvanized…

view full answer...

Answer 2

It is certainly possible to switch from hubs/drums to idler hubs on a trailer axle. For a boat trailer with 3,500 lb axle(s), the Trailer Idler Hub Assembly part #AKIHUB-545-35-G-K or part #AKIHUB-545-35-G-EZ-K for EZ-Lube would be just what you…

view full answer...

Answer 3

Hello Jr, we have exactly what you are looking for. The Kodiak XL ProLube Kit #XLPROLUBE1980KIT will allow you to convert any 3,500 lb hub to an oil bath system. So you can use that along with the 3,500 lb Trailer Hub and Drum Assembly…

view full answer...

Answer 4

From what I was able to find out from my research, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles. Replacement hubs that have these specs typically use a #L68149 inner bearing and #L44649…

view full answer...

Answer 5

There are special seals to convert your 3500lb rotors to oil bath, and they can be replaced with Replacement Seal For 3500-lb Axles #XLPROLUBE1980SEAL. While we do not offer 9-3/4" rotors for your 3500lb boat axle, we do have the Dexter 10"…

view full answer...

Answer 6

That is a Timken seal with the part number 171255TC, so you can use the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 1 #58846 as the replacement or you can get a pair with part #RG06-050.

view full answer...

Answer 7

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

We actually have the Brake Buddy 32220 reverse solenoid available with the Titan Solenoid Valve Replacement Kit #TK71-755-00. The solenoid itself would be an exact replacement and it features the two mounting holes at the bottom like you described…

view full answer...

Answer 10

The grease seal you are looking for is the Grease Seal - Double Lip #010-180-00. This seal has a 1.68 inch inner diameter, 2,33 outer diameter and a width of 0.50 inches, as you can see in the accompanying photo. I went out to the warehouse to check…

view full answer...

Answer 11

The Bearing Kit #BK2-100 will contain the new bearings, races, grease seal, tang washer and cotter pin for replacing the bearings on your 2005 Ranger Trail Boat Trailer. The Inner Bearing #L68149, Inner Race #L68111, Outer Bearing #L44649 and Outer…

view full answer...

Answer 12

We do have a way for you to add a 7-Way connector in the bed of your 2006 Chevy Silverado 2500. The Curt Wiring Kit #C56000 tees right into the back of your current 7-Way via the US CAR connection and then gives you a 10' lead to route the wiring…

view full answer...

Bearing Kit for 2004 Ranger Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching