Correct Backing Plates for etrailer Tandem Axle Teardrop Trailer Fenders

Question

Question:

Can you tell me if backing plate HP82FR is the correct backing plate for Fenders HP94VR and HP44VR? Also if it is not the correct backing plate could you tell me which one goes with each of these fenders? Thanks

asked by: Josh

0

Expert Reply:

The Backing Plate for Tandem Axle Trailer Fender # HP82FR you mention is the correct backing plate for both the Tandem Axle Teardrop Trailer Fenders - Rounded Edges # HP94VR and the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers # HP44VR.

expert reply by: Bryce D

0

Answer 1

We have a couple tandem trailer fenders that are 10-3/4 inches wide like with the part #HP84VR and the #HP74VR which are both 72 inches in length but at the 68 inch length of the #HP64VR

view full answer...

Answer 2

The correct backing for the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers part #HP44VR is the Backing Plate for Tandem Axle Trailer Fender part #HP82FR. Please note, this will need to be tack welded to the backside of the fender.

view full answer...

Answer 3

The Tandem Axle Teardrop Trailer Fenders part #HP44VR which are 66" long measure 9" wide. I have attached a photo below.

view full answer...

Answer 4

When replacing your fenders you want to do your best to match the dimensions to what you currently have. Typically you won't find an exact match to the current fenders. Based on my research it looks like you have a tandem axle trailer with…

view full answer...

Answer 5

When replacing fenders you want to do your best to match the dimensions of your old fenders. Although it is slightly taller, the #HP44VR is going to be the closest match to what you previously had. These measure 66" long x 9" wide x…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Correct Backing Plates for etrailer Tandem Axle Teardrop Trailer Fenders

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching