Availability of Tandem Trailer Fender that is Near 11 inches Wide

Question

Question:

Hello, I am looking for this exact fender in an 11inch width instead of 9inch to cover up the wheels completely on a flatbed trailer. Do you have these in an 11inch width? Thanks,

asked by: Chris K

0

Expert Reply:

We have a couple tandem trailer fenders that are 10-3/4 inches wide like with the part # HP84VR and the # HP74VR which are both 72 inches in length but at the 68 inch length of the # HP64VR

expert reply by: Jameson C

0

Answer 1

The Tandem Axle Teardrop Trailer Fenders part #HP44VR which are 66" long measure 9" wide. I have attached a photo below.

view full answer...

Answer 2

The Backing Plate for Tandem Axle Trailer Fender #HP82FR you mention is the correct backing plate for both the Tandem Axle Teardrop Trailer Fenders - Rounded Edges #HP94VR and the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers #HP44VR.

view full answer...

Answer 3

When replacing fenders you want to do your best to match the dimensions of your old fenders. Although it is slightly taller, the #HP44VR is going to be the closest match to what you previously had. These measure 66" long x 9" wide x…

view full answer...

Answer 4

The correct backing for the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers part #HP44VR is the Backing Plate for Tandem Axle Trailer Fender part #HP82FR. Please note, this will need to be tack welded to the backside of the fender.

view full answer...

Answer 5

Your best route is to replace your entire surge brake assembly as Atwood no longer produces any parts for their brake actuators. The Titan Zinc-Plated Brake Actuator #T47457207K is going to be your best replacement available. It is specific to disc…

view full answer...

Answer 6

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

I checked out your 2007 Exiss Sport 22 trailer and it has a tandem style fender like the part #HP64VR which is for 15 to 16 inch wheels and is overall 68 inches or part #HP94VR which fits 14 to 15 inch wheels which is 65 inches long.

view full answer...

Answer 10

Yes, it is James. The PowerMax 310 RV Toilet item #PM42VR is a Dometic 310 toilet. The PowerMax label is a high-performance flushing system featuring a powerful swirl-jet cleaning action. The PowerMax 310 RV Toilet item #PM42VR has a elongated seat…

view full answer...

Answer 11

The length of a fender is measured from the longest point, at the very bottom of each end across. Then the height is measured from the tallest point, right in the center. For example, the CE Smith Single Axle Trailer Fender #CE17720 is 22-1/2"…

view full answer...

Answer 12

Hey Darrel, to bleed the Dexter Zinc-Plated Brake Actuator #T43397007K that you referenced you would need to use a 2x4 and the safety chains to push on the coupler of the actuator to pressurize it. See attached picture and also the attached help…

view full answer...

Availability of Tandem Trailer Fender that is Near 11 inches Wide

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching