Height of Rubber Portion of Timbren Part # TGMRSB4

Question

Question:

What is the height of the Timbren part # TGMRSB4S? More specifically I am looking for the height of the rubber spring. Thank you.

asked by: Keith

0

Expert Reply:

Just the height of the rubber portion of the Timbren part # TGMRSB4S is 5-1/8 inches.

expert reply by: Jameson C

0

Answer 1

The Timbren Rear Suspension Enhancement System #TGMRYS4 that fit a 2004 Chevy Suburban 1500 and Timbren Rear Suspension Enhancement System #TGMRSB4S that fit a 2004 Chevy Suburban 2500 are different products that install differently and have a…

view full answer...

Answer 2

Timbren makes spacers specifically for the Timbren Rear Suspension Enhancement System #TGMRSB4S on your 2011 Chevrolet Suburban 2500. You have the option of using the Timbren 1" Spacer For Raised Frame Vehicles - 3/8" Bushing #A25723-90AH00…

view full answer...

Answer 3

For your 2005 Chevy Suburban 2500 4x4, I recommend the Timbren Rear Suspension Enhancement System #TGMRSB4S. This will stabilize your vehicle to significantly reduce that sag by using the Aeon Rubber that becomes more rigid as more weight is added.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Height of Rubber Portion of Timbren Part # TGMRSB4

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching