Will the Kodiak 13" Hub and Rotor - 8 on 6-1/2 Work with Oil

Question

Question:

What is the item number re. Item # KRH1378D for the oil bath version of this rotor This is the grease version.

asked by: Bill

0

Expert Reply:

The Kodiak 13" Hub and Rotor part # KRH1378D can be used with either grease or oil, it all comes down to what seal and cap you pair it with since they are not incuded. If you're looking for oil, you'd just need the Kodiak XL ProLube Kit for for 5,200-lb to 6,000-lb Axles part # XLPROLUBE2440KIT.

expert reply by: Conner L

0

Answer 1

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 2

Hi Steve, thanks for reaching out and sharing those details. Based on what you described, it sounds like the issue is likely due to over-greasing the hub. When too much grease is pumped in, it can build excess pressure and force its way past the rear…

view full answer...

Answer 3

The Kodiak Disc Brake Caliper part #KDBC250E which is designed for the Kodiak Disc Brake Kit part #K2HR712E will need to be torqued to 40-50 ft. lbs. per the instructions.

view full answer...

Answer 4

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Will the Kodiak 13" Hub and Rotor - 8 on 6-1/2 Work with Oil

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching