Recommended Idler Hub To Replace Shorelandr SS818 Hub

Question

Question:

My shorelandr trailer says I need a SS818 kit. What replacement hub will fit that hub kit.

asked by: Giulio G

0

Expert Reply:

We have the # AKIHUB-545-2-EZ-2K which is a direct replacement for the Shorelandr SS818 kit you'd mentioned. The only difference in these kits is the brand.

expert reply by: Samuel C

0

Answer 1

Hey Joey, thanks for reaching out. The Hub Saver #HS79FR is designed to replace the existing spindle washer, so you do not want to use both. The original washer gets permanently removed, and the Hub Saver takes its place between the outer bearing and…

view full answer...

Answer 2

Hey Bob, thanks for reaching out. That's a great question, and it's a common point of confusion. The Hub Saver #HS79FR is not designed to keep the hub on the spindle if the castle nut backs off or falls off. The castle nut, washer, and cotter…

view full answer...

Answer 3

For an idler hub that would work as an exact replacement to what you have and is galvanized to help prevent corrosion the part #84545BX that you referenced would work well. It comes with bearings as well.

view full answer...

Answer 4

The load range C Provider ST175/80R13 Radial Trailer Tire #TTWTRTM1758013C has a speed rating of M, which is 81 mph; and there are tires with speed ratings of N, though not for 12 inch tires; for that the highest speed rating the 81 mph M-rated tire.…

view full answer...

Answer 5

I may have a solution for you, however a hub cover like the Phoenix USA QuickTrim #QT545C referenced in your question will not be compatible with your aluminum wheels because of how the lug nuts are recessed. A cover like this will not be able to…

view full answer...

Answer 6

Thanks for the pictures. Either part number hub is going to fit your hub since they both have the same bolt pattern and bearings. The difference is going to be based on the diameter of your trailer wheels. If you have 13-14 inch diameter rims you…

view full answer...

Answer 7

Though it is sometimes possible to identify an axle's capacity based of the hub, it is not always 100% accurate. Due to this, I tell people to not rely on just this alone. As a quick example, if you look at the Dexter Hub #8-259-50BTUC1 and…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommended Idler Hub To Replace Shorelandr SS818 Hub

Product Page this Question was Asked From

Continue Researching