Birch White Ventline Screen Frame and Garnish

Question

Question:

I need 3 pcs vent line screen vd0434 The piece the screen that snaps onto vd0433 The garnish. 3-1/4” D, 1-1/4” flange, 13-1/4” x 13-1/4”

asked by: Shawn M

0

Expert Reply:

Sounds like you are looking for a replacement screen frame which for that you'd need the # BVC0573-32 for if your vent is a powered lift vent or part # BVC0573-31 for if it is a manual lift. Then for the garnish what you would need is the part # VA0445-27.

expert reply by: Jameson C

0

Answer 1

The Ceiling Garnish for Ventline Roof Vent part #VA0445-37 is our best match as it measures 5-5/16" tall and the inside opening measures around 13" - 13-1/4 depending on if you include the flange. I am not sure where you are measuring but…

view full answer...

Answer 2

The correct replacement for your VDO 433 / VDO 434 is going to be the: -Replacement Screen Frame with Screen for Ventline Ventadome Manual Lift Roof Vents #BVC0573-31. This part includes the replacement screen with the screen frame, however if you…

view full answer...

Answer 3

I'm not quite sure what you mean by the "heart", however for your Ventline VD0434 we have the replacement screen frame #BVA0444-32, the replacement lid #BVD0449-A01, and the replacement ceiling garnish #VA0445-28 all available for…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Birch White Ventline Screen Frame and Garnish

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching